Stanford Research Systems RGA100 Скачать руководство пользователя страница 348 | Manualshive

Страница: 348 / 362

background image

Vacuum References

SRS-Vacuum Technology References

29

14. R. M. Hardeveld et. al.”Kinetics of elementary surface reactions studied by static

secondary ion mass spectrometry and temperature programmed reaction
spectroscopy”, J. Mol. Catalysis A: Chem 131 (1998) 199-208

15. Herbert J. Tobias and Paul J. Ziemann, “Compound Identification in Organic

Aerosols Using TPD Particle Beam Mass Spectrometry”, Anal Chem. 71 (1999)
3428-3435

16. D. Schleussner, et. al. “Temperature Programmed Desorption from Graphite”, J. Vac.

Sci. Technol. A17(5) (1999) 2785

17. St. J. Dixon-Warren, et. al. “Butanethiol on Au{100}-(5X20) using a simple

retractable doser”, J. Vac. Sci. Technol. A17(5) (1999) 2982.

Note

: Uses two

SRS

RGA’s

for TPD measurements in an UHV setup.

18. K. W. Bryant et. al. , “Versatile and economic specimen heater for ultrahigh vacuum

applications”, J. Vac. Sci. Technol. A17(5) (1999) 3057

19. St. J. Dixon-Warren, N. Burson, V. Bondzie, L. Zhang, Y. Yu, L. Lucchesi, “A

Simple Single Crystal SampleTemperature Controller Based on Commercial
Components for UHV Surface Science Application”, Rev. Sci. Instr., 69 (1998) 3006

20. M. J. Weiss, C. J. Hagedorn, and W. H. Weinberg, “Observation of gas-phase atomic

oxygen with Ru(001)-p(1x1)-D at 80K, J. Vac. Sci. Technol. A 16(6) (1998) 3521.
Note: an

SRS RGA200

is used to collect the TPD data.

21. Babu R. Chalamala, David Uebelhoer and Robert H. Reuss, “Apparatus for

temperature programmed desorption studies of thin films”, Rev. Sci. Instr. 71 (2000)
320.

Note

: Uses

SRS RGA300

in the TPD setup.

22. C. G. Wiegenstein et. al. , “A virtual approach for automation of temperature

programmed desorption”, Rev. Sci. Instrum., 69(10) (1998) 3707.

23. Tyler Watt and Nicholas Materer, “Temperature programmer for surface science

studies with application to semiconductor surfaces”, J. Vac. Sci. Technol. A20(2)
(2002) 572.

24. Sung-Il Cho, “TPD Study on the decomposition mechanismof Ti(OC

3

H

7

)

4

on

Si(100)”, J. Electrochem. Soc. 148(9) (2001) C599

25. J. T. Yates, Jr., “Design and construction of a semiautomatic temperatue programmed

desorption apparatus for ultrahigh vacuum”, J. Vac. Sci. Technol. A 23(1) (2005)
215.

Membrane Introduction Mass Spectrometry (MIMS)

1. R. T. Short et. al. , “Underwater Mass Spectrometers for in situ Chemical analysis of

the Hydrosphere”, J. Am. Soc. Mass Spectrom. 12 (2001) 676. Note: An RGA is
used in combination with Membrane Introduction Mass Spectrometry (MIMS) to do
underwater analysis of VOCs.

«
...
346
347
348
349
350
...
»

Содержание RGA100











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RGA100

Бренд: AR Страницы: 20

Бренд: dacell Страницы: 22

CP-4900 Micro-GC

Бренд: Varian Страницы: 7

Бренд: Vapotherm Страницы: 2

Бренд: Lasertec Страницы: 28

Бренд: Keller Страницы: 8

Бренд: Kawai Страницы: 72

Бренд: Hammerhead Страницы: 44

Бренд: HTC Страницы: 2

VBOX Touch Motorsport V1

Бренд: Racelogic Страницы: 15

Бренд: PRESIDIUM Страницы: 86

Бренд: Seca Страницы: 280

Бренд: Bante Instruments Страницы: 7

Бренд: dallmeier Страницы: 93

Бренд: YOKOGAWA Страницы: 2

Бренд: LaserLiner Страницы: 44

Бренд: Attonic Страницы: 20

Бренд: Diagtools Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды