Stanford Research Systems RGA100 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 362

background image

Safety and Preparation For Use

SRS Residual Gas Analyzer

iii

Printed in U.S.A.

Safety and Preparation for Use

WARNING!

Dangerous voltages, capable of causing injury or death, are present in this instrument.
Use extreme caution whenever the instrument cover is removed. Do not remove the
cover while the unit is plugged into a live outlet.

Line Cord

The RGA built-in power module option (Opt02) has a detachable, three-wire power cord
for connection to the power source and to a protective ground. The exposed metal parts
of the instrument are connected to the outlet ground to protect against electrical shock.
Always use an outlet which has a properly connected protective ground.

Service

Do not attempt to service or adjust this instrument unless another person, capable of
providing first aid or resuscitation, is present.

Do not install substitute parts or perform any unauthorized modifications to this
instrument. Contact the factory for instructions on how to return the instrument for
authorized service and adjustment.

Fan

The fans in the RGA are required to maintain proper operation. Do not block the vents in
the chassis or the unit may not operate properly.

«
1
2
3
4
5
...
»

Содержание RGA100











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RGA100

Бренд: Wavetronix Страницы: 14

Бренд: Divertug Страницы: 47

Бренд: YOKOGAWA Страницы: 14

Бренд: Kobold Страницы: 44

XL4 SECOND STAGE

Бренд: Apeks Страницы: 21

DGX Gears XTRA Regulator

Бренд: Dive Gear Express Страницы: 26

Бренд: J&D Electronics Страницы: 2

MultiScanner HD800 OneStep

Бренд: Zircon Страницы: 2

Бренд: HERON Страницы: 2

Бренд: Badger Meter Страницы: 12

Бренд: novomatics Страницы: 39

Бренд: SamKnows Страницы: 2

CONTISYS OBD - V3.0

Бренд: VDO Страницы: 144

Бренд: MED Associates Страницы: 6

Бренд: BRUEL & KJAER Страницы: 26

Бренд: Efergy Страницы: 2

Бренд: Lowrey Страницы: 61

Бренд: Soozier Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды