Stanford Research Systems RGA100 Скачать руководство пользователя страница 340

Страница: 340 / 362

Vacuum References

SRS-Vacuum Technology References

47. Phil Danielson, “Matching Vacuum Pump to process”, R&D Magazine, November

2001, p. 53. Note: A quick , concise and useful primer on pump choices.

48. Phil Danielson, “Water Vapor Pumping Produces Unique Problems”, R&D Magazine

Feb 2002, p.59.

49. Bob Langley et. al., “Picking the right pump and the Sizing and matching of Pumps”,

Vacuum Technology and Coating, May 2002, p.23.

50. Terrence Thompson, “Roughing Pumps, Dry and Oil Filled”, Vacuum Technology

and Coating, November 2002, p. 42.

51. Terrence Thompson, “High-Vacuum Pumps”, Vacuum Technology and Coating, Dec

2002, p.52. Note: An up-to date compilation of HV pump technologies and
manufacturers.

52. Jurgen Breitenbach, “The Influence of Diaphragm Pumps on the Hydrogen Partial

Pressure in High Vacuum Systems”, Vacuum Technology and Coating, Jan. 2003,
p.38.

53. Donald Mattox, “Turbomolecular Vacuum Pumps”, Vacuum Technology and

Coating, Jan 2003, p.24.

54. Ron Hawranko, “How to Choose a TurboPump”, R&D Magazine, July 2003, p. 46

55. Phil Danielson, “Matching Cryopumping Techniques to Applications”, R&D

Magazine, Oct. 2003, p. 36.

56. Kimo Welch, “A century of Capture Pumping Technology- Sputter-Ion pumping”,

Vacuum Technology and Coating, June 2004, p. 18.

57. A. D. Chew, et. al., “Considerations for Primary Vacuum Pumping in Mass

Spectrometry Systems”, Spectroscopy 20(1) (2005) 44.

58. Bob Langley and Paul LaMarche, “Criteria for Selection of Pumping Fluids for

Diffusion Pumps and of Vacuum Greases”, Vacuun Technology and Coating,
December 2004, p. 20,

59. Kimo Welch, “Titanium Sublimation Pumps How They Work”, Vac. Technology &

Coating, Dec 2004, p. 32.

60. Kimo M. Welch, “Titanium Sublimation Pump Sources”, Vacuum Technology &

Coating, January 2005, p. 28.

61. Donald Mattox, “Cryopumps, Sorption Pumps and Cryopanels”, Vacuum

Technology & Coating, Jan 2005, p. 36.

62. Robert Langley, “Turbomolecular Pumps”, Vac. Technology & Coating, February

2005, p. 32.

Содержание RGA100











































































































































































































































































































































































Результаты поиска

Содержание RGA100

Отзывы:

Похожие инструкции для RGA100

Бренды по названию

Популярные бренды

Stanford Research Systems RGA100, Руководство по эксплуатации и программированию

Результаты поиска

Содержание RGA100

Отзывы:

Похожие инструкции для RGA100

Бренды по названию

Популярные бренды