manualshive.com logo in svg

Stanford Research Systems RGA100, Руководство по эксплуатации и программированию


Поделиться
Скачать
background image

 

 

Basic Troubleshooting 

9-7 

 

SRS Residual Gas Analyzer 

causing severe overpressures. 

If the pressure is OK ( i.e. <10

-4

 Torr), check for shorts in the ionizer assembly.  

Using an ohmmeter check the conductance between the ionizer’’s connectors and 
the vacuum system. (The ionizer feedthrus can be easily identified using the 
drawings in the RGA Assembly Chapter). 

 If a short is detected, remove the probe from the vacuum system , inspect the 
ionizer and fix any shorts. Note: Use the information in the RGA Maintenance 
chapter to remove the repeller and/or service the ionizer. 

If the short is still present after that, remove the  RGA Cover Nipple and inspect 
the rest of the probe for other sources of shorts (i.e. misalignments, loose screws, 
etc.).  If no short is detected, the Thoria coating of the filament might be 
damaged. 

Inspect the filament (best with a magnifying glass) and look for large sections of 
Thoria coating missing. If a problem is suspected replace the filament using the 
procedure in the RGA Maintenance chapter.  If the filament still does not turn on, 
contact SRS. 

Error Code: 

FL7

Type of Error:

Filament ““Background Protection Mode””. 

Error Message: 

Filament Error: No filament detected. 

Error Cause: 

No filament was detected after an attempt was made to establish emission current 
in the ionizer. The Error and Burnt LED’’s are turned on by this error. 

Troubleshooting:

A probe must be connected to the ECU. 
The probe must have a filament. 
The filament must have at least one intact (i.e. conductive) side. Use an ohmmeter 
to check continuity across the filament (The two filament feedthrus can be easily 
identified using the drawings in the RGA Assembly Chapter). 
The probe must be correctly connected to the ECU. Tighten the locking screws of 
the box 

Error Code: 

PS6

Type of Error:

24VDC P/S. 

Error Message: 

External 24V P/S error: voltage <22V. 

Error Cause: 

Voltage output of 24VDC Power Supply is under the acceptable 22-26V DC 
range. The Power LED is turned off and the Error LED is turned on instead. 

Troubleshooting:

Check the voltage output of the external power supply with a voltmeter. 
Adjust the voltage to 24 V in adjustable external supplies or replace the power 
supply altogether if necessary. 
Contact SRS if your unit has a built-in power supply (Option 02). 

Содержание RGA100











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RGA100

Unico SQ Series Service Manual preview
SQ Series
Бренд: Unico Страницы: 96
K&K Sound Bass Master Rockabilly Product Manual preview
Bass Master Rockabilly
Бренд: K&K Sound Страницы: 2
National Instruments NI 9219 Getting Started Manual preview
NI 9219
Бренд: National Instruments Страницы: 38
X-Rite DensiEye 100 Reference Manual preview
DensiEye 100
Бренд: X-Rite Страницы: 50
Energic Plus MPD-1007E Manual preview
MPD-1007E
Бренд: Energic Plus Страницы: 12
Sig Sauer BUCKMASTERS 1500 Manual preview
BUCKMASTERS 1500
Бренд: Sig Sauer Страницы: 2
sebaKMT Correlux C-3 User Manual preview
Correlux C-3
Бренд: sebaKMT Страницы: 131
Omega HHM598F Manual preview
HHM598F
Бренд: Omega Страницы: 13
Apogee SL-510 Owner'S Manual preview
SL-510
Бренд: Apogee Страницы: 18
Feasa ICT Series User Manual preview
ICT Series
Бренд: Feasa Страницы: 145
Nauticam WIDE ANGLE CONVERSION PORT 2 Instruction Manual preview
WIDE ANGLE CONVERSION PORT 2
Бренд: Nauticam Страницы: 12
LOVATO ELECTRIC DMED300T2MI Instruction Manual preview
DMED300T2MI
Бренд: LOVATO ELECTRIC Страницы: 9
Vaisala WAV252 Quick Reference Manual preview
WAV252
Бренд: Vaisala Страницы: 2
SKF 800030 Installation And Maintenance Manual preview
800030
Бренд: SKF Страницы: 12
Velleman NETBPEM3 User Manual preview
NETBPEM3
Бренд: Velleman Страницы: 21
Komshine KPM-35 User Manual preview
KPM-35
Бренд: Komshine Страницы: 2
bihl+Wiedemann BWU2427 Installation Instructions Manual preview
BWU2427
Бренд: bihl+Wiedemann Страницы: 16
LaserLine QUAD 1000HDD Owner'S Manual preview
QUAD 1000HDD
Бренд: LaserLine Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды