manualshive.com logo in svg

Stanford Research Systems RGA100, Руководство по эксплуатации и программированию


Поделиться
Скачать
background image

 

 

Vacuum References 

 

SRS-Vacuum Technology References 

    27

2. Sharrill Dittmann, ““High Vacuum Standard and its use””, NIST Special Publication 

250-34. U.S. Department of Commerce , National Institute of Standards and 
Technology,  

3. K. E. McCulloh et. al. ““Summary Abstract: The national Bureau of standards orifice-

flow primary high vacuum standard””, J. Vac. Sci. Technol. A4(3) (1986) 362 

4. Tilford, C. et. al. , JVST A6(5) (1988) 2853, ““The National Bureau of Standards 

primary high-vacuum standard””. 

5. K. E. McCulloh et. al. ““Low-range flow-meters for use with vacuum and leak 

standards””, J. Vac. Sci. Technol. A5(3) (1987) 376 

6. P. D. Levine et. al. JVST A14(3) (1996) 1297, ““A primary high vacuum calibration 

station for industrial applications””. 

7. P. D. Levine et. al. ““Development of a primary standard UHV calibration station””, J. 

Vac. Sci. Technol. A 12(4) (1994) 1727 

8. P. D. Levine et. al. ““Precision gas flowmeter for Vacuum calibration””, J. Vac. Sci. 

Technol. A 15(3) (1997) 747 

9. J. K. Fremerey, J. Vac. Sci. Technol. A3 (3) (1985) 1715, ““The Spinning Rotor 

Gauge””.

10. J. Setina, ““Two Point calibration scheme for the linearization of the spinning rotor 

gauge at transition regime pressures””, J. Vac. Sci. Technol. A 17(4) (1999) 2086 

11. Sharrill Dittmann et. al. , ““The Molecular drag gauge as a calibration Standard””, J. 

Vac. Sci. Technol. A7(6) (1989) 3356 

12. K. Jousten, A.R. Filippelli, C.R. Tilford, and F. J. Redgrave, ““Comparison of the 

standards for high and ultrahigh vacuum at three national standards laboratories””, J. 
Vac. Sci. Technol. A 15 (4) (1997) 2395 

13. J. P. Looney et. al. ““PC Based spinning rotor gage controller””, Rev. Sci. Instr. 65(9) 

(1994) 3012 

14. James Basford et. al. ““Recommended practice for the calibration of Mass 

spectrometers for partial pressure analysis””, J. Vac. Sci. Technol. A 11(3) (1993) A22 

15. P. Mohan ““Vacuum Gauge calibration at the NPL (India) using orifice flow method”” 

Vacuum 51(1998) 69 

16. R. E. Ellefson, A. P. Miller, ““Recommended practice for calibrating vacuum gauges 

of the thermal conductivity type””, J. Vac. Sci. Technol. A 18(5) (2000) 2568-2577. 

17. Kimo M. Welch, ““A Poor-Man’’s Traceable High Vacuum Gauge Calibration 

System””, Vacuum Technology and Coating, Nov/Dec 2000, p. 8. Note: This is a 
great article on how to make a simple calibration station for HV Gauge calibration.

Содержание RGA100











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RGA100

ABB Navigator 550 Commissioning Instructions preview
Navigator 550
Бренд: ABB Страницы: 8
Kane 3500 Manual preview
3500
Бренд: Kane Страницы: 20
NCTE 2300 Series Technical Information And Instructions preview
2300 Series
Бренд: NCTE Страницы: 10
Major tech MT975 Instruction Manual preview
MT975
Бренд: Major tech Страницы: 16
Zoetis AlphaTRAK Instructions For Use preview
AlphaTRAK
Бренд: Zoetis Страницы: 2
Sage SIP Operation And Instruction Manual preview
SIP
Бренд: Sage Страницы: 68
Lasertec TruPulse L2 Quick Reference Field Manual preview
TruPulse L2
Бренд: Lasertec Страницы: 21
ISKRAEMECO MT174 Manual preview
MT174
Бренд: ISKRAEMECO Страницы: 12
Ravaglioli RAVTD1760WS Series Service Manual preview
RAVTD1760WS Series
Бренд: Ravaglioli Страницы: 24
AKCP ILPM Manual preview
ILPM
Бренд: AKCP Страницы: 16
Swann AMI Codes-II Operator'S Manual preview
AMI Codes-II
Бренд: Swann Страницы: 106
Saturn South SS9007.3 Mini CT Meter User Manual preview
SS9007.3 Mini CT Meter
Бренд: Saturn South Страницы: 18
envea STACK 710 User Manual preview
STACK 710
Бренд: envea Страницы: 68
Prosense FMM100-1001 Operating Instructions Manual preview
FMM100-1001
Бренд: Prosense Страницы: 35
RBR ecom-JN Operating Instructions Manual preview
ecom-JN
Бренд: RBR Страницы: 32
Fema Electronica M40-A User Manual preview
M40-A
Бренд: Fema Electronica Страницы: 24
RADWAG PUE HX7 Quick Start Manual preview
PUE HX7
Бренд: RADWAG Страницы: 12
Liquivision XEN User Manual preview
XEN
Бренд: Liquivision Страницы: 84

Бренды по названию

Популярные бренды

Загрузить еще бренды