Stanford Research Systems RGA100 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 362

background image

1-2

Unpacking

SRS Residual Gas Analyzer

Unpacking

Before You Open the Box

1.

To reduce the chance of contamination, do not remove the probe from its plastic
shipping container until moments before it is ready to be installed in the vacuum
system.

2.

Avoid contaminating the RGA gauge. Follow good high vacuum practice. Set aside a
clean, dust free, work area next to the vacuum port before installation begins.

3.

Please read and follow all installation instructions in this chapter to insure that the
optimum performance of the instrument is not compromised during the installation
process.

4.

Do not power up the instrument until it is instructed in the installation procedure.

5.

Take a moment at this time to read the CDEM Handling and Care section of the
RGA Maintenance chapter if your unit includes the electron multiplier option
(Option 01).

6.

Do not operate the RGA if the pressure in the chamber is greater than 10

-4

Torr.

Consult Appendix B for information on Pressure Reduction Systems.

7.

Read the General Operation chapter of this manual for an overview of the instrument
and its functions.

8.

Inspect all components of the SRS RGA System upon unpacking. Report any
damage to Stanford Research Systems immediately. Compare the contents of the
shipping container with the Checklist below and report any discrepancies.

Checklist

Standard Equipment / Supplies

1.

One RGA Probe (in sealed plastic container.)

2.

One Electronics Control Unit box.

3.

Compact Disk with RGA Windows software.

4.

DB9-DB9 RS232 cable (25’ length).

5.

Operating Manual and Programming Reference.

Accessories

1.

Female DB-9 cable connector, with two wires for 24V power supply connection (not
provided with Option 02).

Optional Equipment

1.

Option 01 Electron multiplier, with HVPS. Preinstalled at the factory.

«
...
18
19
20
21
22
...
»

Содержание RGA100











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RGA100

Бренд: Kane Страницы: 4

Бренд: Oakton Страницы: 69

Бренд: Parkside Страницы: 114

PLUS 3631 Series

Бренд: insize Страницы: 1

Бренд: Datakom Страницы: 28

Бренд: ACCRETECH Страницы: 104

Бренд: D-tect Systems Страницы: 28

Бренд: BANTE Страницы: 17

Бренд: E+E Elektronik Страницы: 4

Бренд: yellow jacket Страницы: 16

60 VioLab Series

Бренд: XS Instruments Страницы: 41

Бренд: Toner Страницы: 7

Бренд: K&K Sound Страницы: 2

Бренд: Grace Industries Страницы: 183

Бренд: ROCTEST Страницы: 29

SI Analytics Lab 855

Бренд: Xylem Страницы: 60

Бренд: Dairymaster Страницы: 14

Бренд: PrimeLab Страницы: 353

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды