Stanford Research Systems RGA100 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 362

background image

4-6

Rear Panel

SRS Residual Gas Analyzer

LED Functionality

LED's on the rear panel of the ECU provide constant feedback on the status of the
filament, electron multiplier, electronics system, probe and communications, and alert the
user of any detected errors. This section describes in detail the function of each LED.

RS232/DCE/28.8k

+24VDC @ 2.5A

Power

Filament

Degas

ElecMult

RS232

Error

Leak

Burnt

Lock

Lock

STATUS LEDs

ERROR

LEDs

Figure 5 ECU LED’s

STATUS (Green) LED’s

Power

: The Power LED is turned on whenever the RGA is successfully powered up.

When power is applied to the ECU, a firmware routine automatically checks the external
voltage level and turns on the Power LED if the voltage is within the acceptable range of
24 +/-2 V DC. The same test is performed in units with built-in power modules (Option
02) to check the voltage output of the internal switching power supply. If the check fails,
the red Error LED is turned on instead to indicate the problem.

Note: A check on the external power supply can be performed at any time during
operation using the EP? diagnostic command.

Filament

: The Filament LED indicates the presence of electron emission current in the

RGA’s ionizer. It is turned on when a finite emission current is requested by the user and
during Degas processes. It is turned off when the user requests a null emission current or
when a filament error condition (i.e. overpressure, worn out or burnt filament) is
detected and the filament emission is turned off.

Note: Filament error conditions are easily diagnosed with the help of the Leak and Burnt
LED and the assortment of diagnostic checks built into the firmware and supported by the
RGA Windows program.

Degas

: The Degas LED is activated during Filament Degas processes.

The Filament LED is also activated during a Degas.
The ElecMult LED is turned off during a Degas.

«
...
70
71
72
73
74
...
»

Содержание RGA100











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RGA100

A300 Sport.Tool

Бренд: Navman Страницы: 1

Бренд: Hach Страницы: 96

Бренд: Endress+Hauser Страницы: 88

Бренд: CAS Corporation Страницы: 20

Бренд: Wacom Страницы: 23

Thruline 4020 Series

Бренд: Bird Electronic Страницы: 59

Mini HD Recorder

Бренд: Green Feathers Страницы: 8

Бренд: Smartwares Страницы: 2

DUSTHUNTER SB30

Бренд: SICK Страницы: 72

Бренд: East Tester Страницы: 23

Class 3400 Meter

Бренд: E-Mon Страницы: 20

Бренд: ENSONIQ Страницы: 260

Бренд: mru Страницы: 32

Бренд: IME Страницы: 14

AquaInform Sycon 2500

Бренд: WACON Страницы: 52

Бренд: Keysight Страницы: 41

Ophir Spiricon BeamWatch Standard

Бренд: MKS Страницы: 20

VarioView Camera

Бренд: LaserLiner Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды