manualshive.com logo in svg

Stanford Research Systems RGA100, Руководство по эксплуатации и программированию


Поделиться
Скачать
background image

8-12  Filament Replacement 

SRS Residual Gas Analyzer 

Probe Assembly

RGA Mounting Flange

Ionizer

Vacuum Chamber

Vacuum Port

RGA Cover Nipple

Figure 2 Probe Removal for Filament Replacement

6. Immediately carry the probe to a clean, dust-free area and secure it in an upright 

position.

Avoid contamination 

using handling procedures compatible with high 

vacuum requirements. 

7. Using the clean, flat-head screwdriver remove the single screw that connects the 

repeller to the longer filament rod and pull out the cage exposing the filament and the 
anode grid. 

8. Before replacing the filament, visually inspect the entire ionizer. Check for loose, 

damaged, misaligned and contaminated components. Some discoloration of the 
ionizer parts is common, but heavy buildup on the grids and plates is a sign of severe 
contamination. If problems are detected, a complete ““Ionizer Replacement”” 
procedure should be carried out at this time. Otherwise, continue with the filament 
replacement procedure. 

9. Inspect the filament, and become acquainted with the way in which it is mounted on 

the filament rods: The SRS RGA filament is of a circular shape and made out of very 
thin, thoria-coated iridium wire. Two platinum tabs, spot-welded at opposite ends of 
its circumference, provide electrical connection to the rods that deliver the power 
during emission. Precision machined slots define the exact placement of the filament 
tabs along the two rods and a small ““screw and nut”” set secure each tab in place. 

10. Without removing the nuts, loosen the two screws that hold the filament in place 

enough to pull the filament out the ionizer assembly. Discard the old filament.  

11. Leave enough clearance between each nut and the top of its corresponding alignment 

slot to slide the platinum tabs of the new filament during installation.  

12. Open the filament box and pick up the filament by one of its platinum tabs with the 

clean tweezers. 

13. Very carefully slide the filament into position, until the platinum tabs fall into the 

slots.

Do not bend or twist the filament. Do not scratch the Thoria coating!

14. Tighten the screws while pressing the nuts against the rods with the tweezers, making 

sure the tabs are centered in the slots.

Содержание RGA100











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RGA100

Kanomax S200 Series Quick Manual preview
S200 Series
Бренд: Kanomax Страницы: 2
Keithley 6512 Instruction Manual preview
6512
Бренд: Keithley Страницы: 156
Dallas Brass WindMaster Instructions Manual preview
WindMaster
Бренд: Dallas Brass Страницы: 19
Daewoo D-60 User Manual preview
D-60
Бренд: Daewoo Страницы: 17
JENCO EC3840 Operation Manual preview
EC3840
Бренд: JENCO Страницы: 13
ISKRAEMECO MT174 Manual preview
MT174
Бренд: ISKRAEMECO Страницы: 12
Ravaglioli RAVTD1760WS Series Service Manual preview
RAVTD1760WS Series
Бренд: Ravaglioli Страницы: 24
King Instrument 7710 Series Installation Instructions preview
7710 Series
Бренд: King Instrument Страницы: 5
Armstrong Monitoring Corporation AMC-CD2 Instruction Manual preview
AMC-CD2
Бренд: Armstrong Monitoring Corporation Страницы: 12
Veeco Dektak 150 User Manual preview
Dektak 150
Бренд: Veeco Страницы: 349
GrainPro GPO2-AN Instruction Manual preview
GPO2-AN
Бренд: GrainPro Страницы: 7
Caen DT5740 Technical Information Manual preview
DT5740
Бренд: Caen Страницы: 50
OHAUS STARTER 3100C Instruction Manual preview
STARTER 3100C
Бренд: OHAUS Страницы: 84
PASCO PASPORT PS-2174 Instruction Sheet preview
PASPORT PS-2174
Бренд: PASCO Страницы: 4
Unipro UniGo 3005 Quick Manual preview
UniGo 3005
Бренд: Unipro Страницы: 2
pts Diagnostics A1CNow Quick Reference Manual preview
A1CNow
Бренд: pts Diagnostics Страницы: 2
Spectroline LeakTracker OIL-GLO ULTRA Instruction Manual preview
LeakTracker OIL-GLO ULTRA
Бренд: Spectroline Страницы: 12
3M SP-SE-2-1/1 User Manual preview
SP-SE-2-1/1
Бренд: 3M Страницы: 168

Бренды по названию

Популярные бренды

Загрузить еще бренды