manualshive.com logo in svg

Stanford Research Systems RGA100, Руководство по эксплуатации и программированию


Поделиться
Скачать
background image

 

Contents 

SRS Residual Gas Analyzer 

vi 

Chapter 3 RGA Quadrupole Probe 

3-1 

 Introduction ............................................................................................................................................. 3-2 

 Ionizer ...................................................................................................................................................... 3-3 

Description .................................................................................................................................. 3-3 

Principle of operation ................................................................................................................. 3-3 

Parameter Settings ..................................................................................................................... 3-4 

 Quadrupole mass filter........................................................................................................................... 3-7 

Description .................................................................................................................................. 3-7 

Principle of operation ................................................................................................................. 3-8 

Mass Range, Resolution and Throughput ............................................................................... 3-9 

Zero Blast Suppression............................................................................................................ 3-12 

 Ion Detector ........................................................................................................................................... 3-13 

Description ................................................................................................................................ 3-13 

Faraday Cup operation............................................................................................................. 3-14 

Electron Multiplier Operation .................................................................................................. 3-14 

 Hardware modifications ....................................................................................................................... 3-18 

Repeller and anode grid modifications .................................................................................. 3-18 

Repeller removal ....................................................................................................................... 3-19 

Operation without a filament ................................................................................................... 3-19 

W filament replacement............................................................................................................ 3-19 

RGA Cover Nipple Replacement ............................................................................................. 3-20 

Chapter 4 RGA Electronics Control Unit 

4-1 

 Introduction ............................................................................................................................................. 4-2 

 Front Panel .............................................................................................................................................. 4-3 

 Rear Panel................................................................................................................................................ 4-4 

[email protected] Connector .......................................................................................................... 4-4 

RS232/DCE/28.8k Connector ..................................................................................................... 4-5 

LED’s............................................................................................................................................ 4-5 

Locking Knobs ............................................................................................................................ 4-5 

Power entry module (Option 02) ............................................................................................... 4-5 

LED Functionality ....................................................................................................................... 4-6 

STATUS (Green) LED’s .......................................................................................................... 4-6 
ERROR  (Red) LED’s .............................................................................................................. 4-7 

 Electrometer ............................................................................................................................................ 4-8 

Detection limit vs. scan rate ...................................................................................................... 4-8 

Adjusting the Zero of the Ion Detector ..................................................................................... 4-9 

Содержание RGA100











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RGA100

Kawai ES100 Technical Speci? Cations preview
ES100
Бренд: Kawai Страницы: 5
Jata hogar 80 Instructions Manual preview
80
Бренд: Jata hogar Страницы: 12
2B Technologies 306 Start-Up Instructions preview
306
Бренд: 2B Technologies Страницы: 4
Yamaha 142 Quick Operation Manual preview
142
Бренд: Yamaha Страницы: 2
Kane 3500 Manual preview
3500
Бренд: Kane Страницы: 20
Daewoo DSD-9502T Retuning preview
DSD-9502T
Бренд: Daewoo Страницы: 2
Weller WA2000 Instruction Manual preview
WA2000
Бренд: Weller Страницы: 9
PCB Piezotronics 393B32 Installation And Operating Manual preview
393B32
Бренд: PCB Piezotronics Страницы: 15
H. HERMANN EHLERS F010-P Operation Manual preview
F010-P
Бренд: H. HERMANN EHLERS Страницы: 40
Fora GTel Owner'S Manual preview
GTel
Бренд: Fora Страницы: 64
E+H Micropilot S FMR533 Manual preview
Micropilot S FMR533
Бренд: E+H Страницы: 12
National Instruments AT-AI-16XE-10 Programmer'S Manual preview
AT-AI-16XE-10
Бренд: National Instruments Страницы: 169
RS PRO SLM 1353M Instruction Manual preview
SLM 1353M
Бренд: RS PRO Страницы: 41
Vega EL 11 Operating Instructions Manual preview
EL 11
Бренд: Vega Страницы: 52
Vectronics SWR-584C Owner'S Manual preview
SWR-584C
Бренд: Vectronics Страницы: 28
aquilar AquiTron AT-WFM Installation & Operation Instructions preview
AquiTron AT-WFM
Бренд: aquilar Страницы: 20
Chauvin Arnoux PHYSICS line C.A 832 User Manual preview
PHYSICS line C.A 832
Бренд: Chauvin Arnoux Страницы: 43
NARDA SRM-3006 Operating Manual preview
SRM-3006
Бренд: NARDA Страницы: 240

Бренды по названию

Популярные бренды

Загрузить еще бренды