manualshive.com logo in svg

Stanford Research Systems RGA100, Руководство по эксплуатации и программированию


Поделиться
Скачать
background image

28 

Vacuum References 

SRS-Vacuum Technology References 

18. S. P. Hansen, ““ Vacuum Instrument Calibration & Personnel Training Boost 

Productivity””, Vacuum Technology &Coating, April 2001, p. 46. 

19. Kimo Welch, ““Verifying a Leak Checker’’s Sensitivity to 10

-12

 TorrL/s (He)””, 

Vacuum Technology &Coating, April 2001, p.12. 

Temperature Programmed Desorption 

1. P.A. Redhead, Vacuum, 12 (1962) 203, ““Thermal Desorption of Gases””. Note: A 

““Classic”” paper with the basics. 

2. J. T. Yates, Jr. et. al. , Surface Science 322 (1995) 243, ““CO adsorption on stepped 

Pd (112): studies by thermal and electron stimulated desorption””. 

Note

: Read 

anything by Yates. 

3. J. T. Yates, Methods in Experimental Physics, vol. 22 , Academic Press Orlando 

1985, p. 425. 

4. John T. Yates, ““Experimental Innovations in Surface Science. A guide to Practical 

Laboratory Methods and Instruments””, Springer-Verlag, New York, 1997. 

Note

:

Everything starting at page 366 and above is essential information.  

5. J. L. Gland, et. al. J. Phys. Chem. 100 (1996) 11389, ““Temperature Programmed 

Desorption Spectra of Systems with Concentration Gradients in the Solid Lattice”” 

6. J. L. Gland, et. al. Surface Science 355 (1996) L385, ““The effects of exposure time 

and pressure on the TPD spectra of systems with bulk states”” 

7. A. M. de Jong et. al. ““Thermal Desorption Analysis: Comparative test of ten 

commonly applied procedures””, Surface Science 233 (1990) 355. 

Note

: You must get 

this paper if you do not have it yet! 

8. J. Gunster et. al., ““Mg clusters on MgO surfaces: Characterization with metastable 

impact electron spectroscopy, ultraviolet photoelectron spectroscopy and temperature 
programmed desorption, A 17(4) (1999) 1657 

9. V. A. Bondzie, S. C. Parker and C. T. Campbell, ““Oxygen Adsorption on well 

defined gold particles on TiO

2

 (110), J. Vac. Sci. Technol. A 17 (4) (1999) 1717 

10. Li Chen and Jeff Kelber, ““Polymerized C-Si films on metal substrates: Cu 

adhesion/diffusion barriers for ultralarge scale integration?, J. Vac. Sci. Technol. 
A17(4) (1999) 1968 

11. J. W. Niemantsverdriet et. al. ““The compensation effect in thermal desorption of 

adsorbate systems with lateral interactions””, J. Vac. Sci. Technol. A 6 (3) (1998) 757 

12. J. W. Niemantsverdriet et. al., ““Thermal desorption of strained monoatomic Ag and 

Au layers from Ru(001)””, J. Vac. Sci. Technol. A 5(4) (1987) 875 

13. R. M. Hardeveld et. al. ““The adsorption of NH3 on Rh(111)””, Surface Science 

369(1996) 23-35 

Содержание RGA100











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RGA100

rainforest EMU Quick Start Manual preview
EMU
Бренд: rainforest Страницы: 2
Valor 203 Installation Manual preview
203
Бренд: Valor Страницы: 13
Campbell 108 Instruction Manual preview
108
Бренд: Campbell Страницы: 31
Macnaught MH450 Manual preview
MH450
Бренд: Macnaught Страницы: 4
WATERGUARD Puddle Installation Manual preview
Puddle
Бренд: WATERGUARD Страницы: 2
Yamaha Clavinova CLP-311 Mode D'Emploi preview
Clavinova CLP-311
Бренд: Yamaha Страницы: 29
Yamaha ARIUS YDP-S52 Quick Operation Manual preview
ARIUS YDP-S52
Бренд: Yamaha Страницы: 2
Yamaha Arius YDP-144 User Manual preview
Arius YDP-144
Бренд: Yamaha Страницы: 15
Yamaha Arius YDP-105 Midi Reference preview
Arius YDP-105
Бренд: Yamaha Страницы: 3
Yamaha Alto Horn, Baritone, Euphonium Mode D'Emploi preview
Alto Horn, Baritone, Euphonium
Бренд: Yamaha Страницы: 22
Yamaha Clavinova CLP-320 Quick Operation Manual preview
Clavinova CLP-320
Бренд: Yamaha Страницы: 2
Yamaha 9000 Pro Service Manual preview
9000 Pro
Бренд: Yamaha Страницы: 20
Yamaha Clavinova CVP-601 Reference Manual preview
Clavinova CVP-601
Бренд: Yamaha Страницы: 98
Yamaha Electone CSY-1 Manual preview
Electone CSY-1
Бренд: Yamaha Страницы: 28
Yamaha YX500R Owner'S Manual preview
YX500R
Бренд: Yamaha Страницы: 12
Apeks XL4 SECOND STAGE Technical Maintenance Manual preview
XL4 SECOND STAGE
Бренд: Apeks Страницы: 21
Industrial Scientific iTrans 77023554 Manual preview
iTrans 77023554
Бренд: Industrial Scientific Страницы: 94
Kirby Morgan KMB-18 A/B Operation And Maintenance Manual preview
KMB-18 A/B
Бренд: Kirby Morgan Страницы: 101

Бренды по названию

Популярные бренды

Загрузить еще бренды