manualshive.com logo in svg

Stanford Research Systems RGA100, Руководство по эксплуатации и программированию


Поделиться
Скачать
background image

8-22  Quadrupole filter cleaning 

SRS Residual Gas Analyzer 

Procedure

1.

Read all warnings

 at the beginning of this chapter before attempting to service the 

probe.

2. Set up in advance a clean dust-free working area where to carry out this procedure. 

3. Turn off the RGA and disconnect the ECU from the probe. 

4. Wait for the probe to cool down for at least 30 minutes after the emission is turned 

off.

Severe burns can result if the probe is handled too soon

.

5. Without disconnecting the cover nipple from the vacuum port, remove the six bolts 

from the feedthru flange at the end of the probe and carefully slide the entire probe 
assembly out of the vacuum system. The ionizer, the filter, and the detector are now 
fully exposed and easily accessible. 

Probe Assembly

Feedthru Flange

Ionizer

Vacuum Chamber

Vacuum Port

RGA Cover Nipple

Figure 5 Probe Removal for Quadrupole Filter Cleaning 

6. Carry the probe to a clean, dust free area immediately. 

Avoid contamination 

using

handling procedures compatible with high vacuum requirements. 

7. Hold the probe in a secure upright position and do a thorough visual inspection of the 

unit. Check for loose, damaged, misaligned and severely contaminated components.   
If excessive contamination is evident take the necessary steps to identify and 
eliminate the contamination sources in the vacuum system.  Carefully inspect the 
ionizer and, if any problems are detected, replace the filament and/or the ionizer as 
part of this maintenance procedure.  Inspect the CDEM for signs of arcing and 
contamination. If necessary replace the CDEM as part of this maintenance procedure.  

8.

Head disassembly:

 Only a rough outline of the complete disassembly of the probe is 

presented here. Use the 

RGA Assembly Drawing

 of Chapter 9 as a visual aid during 

the process. 

Note the placement of all parts and their orientation before disassembly! 

Begin by removing the filament following the necessary steps from the ““Filament 
Replacement”” procedure described in this chapter. Be very careful not to damage the 
thoria coating if you intend to use the same filament during reassembly. 
Next, remove the CDEM following steps from the ““CDEM Replacement”” procedure. 
Store the multiplier in a dry box or desiccator.  Loosen the seven screws that fasten 
the 1/8”” diameter rods to the feedthru connectors, and remove the bowed e-clip from 
the exit plate align rod that is located right above the CDEM. You can now separate 

Содержание RGA100











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RGA100

Keithley 580 Operator'S Manual preview
580
Бренд: Keithley Страницы: 73
Van Walt GA5000 Quick Start Manual preview
GA5000
Бренд: Van Walt Страницы: 2
Valeport 106 Operating Manual preview
106
Бренд: Valeport Страницы: 27
ICT SFM1 Quick Start Manual preview
SFM1
Бренд: ICT Страницы: 48
OfiTE 2040 Instruction Manual preview
2040
Бренд: OfiTE Страницы: 67
Bacharach 2810 Operation & Maintenance Manual preview
2810
Бренд: Bacharach Страницы: 28
Xylem TM 40 Operating Manual preview
TM 40
Бренд: Xylem Страницы: 24
Yamaha Electone 405 Data List preview
Electone 405
Бренд: Yamaha Страницы: 84
Omega DP-7600 User Manual preview
DP-7600
Бренд: Omega Страницы: 31
DriveTest BIA Class 2 Manual preview
BIA Class 2
Бренд: DriveTest Страницы: 24
Mannix DCFM8906 Operating Instructions preview
DCFM8906
Бренд: Mannix Страницы: 5
Savant DigiFlow 6710M-22 Quick Start Manual preview
DigiFlow 6710M-22
Бренд: Savant Страницы: 3
Fora GTel Owner'S Manual preview
GTel
Бренд: Fora Страницы: 64
Chauvin Arnoux PHYSICS line C.A 832 User Manual preview
PHYSICS line C.A 832
Бренд: Chauvin Arnoux Страницы: 43
SEFRAM MW 3360 User Manual preview
MW 3360
Бренд: SEFRAM Страницы: 31
Rubicson 48829 Manual preview
48829
Бренд: Rubicson Страницы: 4
ZIEHL TR660IP Operating Manual preview
TR660IP
Бренд: ZIEHL Страницы: 37
XPOtool 63039 Operation Manual preview
63039
Бренд: XPOtool Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды