Stanford Research Systems RGA100 Скачать руководство пользователя страница 336 | Manualshive

Страница: 336 / 362

background image

Vacuum References

SRS-Vacuum Technology References

17

17. Greg A. Pfister, “Eliminating Seal Contamination in Semiconductor Process

Equipment”, Vacuum Technology &Coating, June 2000, p. 29.

18. L. Layden and D. Wadlow, “High Velocity carbon dioxide snow for cleaning

vacuum system surfaces”, J. Vac. Sci. Technol. A 8(5) (1990) 3881.

19. Phil Danielson, “Reduce Water Vapor in Vacuum Systems”, R&D Magazine,

September 2000, S-10.

20. Rita Mohanty, “Use of Getters in Hermetic Packages”, Vacuum Technology and

Coating, October 2000, p. 41.

21. Andrew D. Johnson, et.al., “Reducing PFC gas emissions from CVD chamber

cleaning”, Solid State Technology, December 2000, p. 103.

22. Mark Higgins, “High Sensitivity Leak Detection, Done Simply”, Vacuum

Technology &Coating, January 2001, p. 42.

23. Donald Mattox, “Water and Water Vapor”, Vacuum Technology and Coating, Jan

2001, p. 58.

24. Phil Danielson, “Desorbing Water in Vacuum Systems: Bakeout or UV?”, R&D

Magazine, January 2001, p. 57.

25. Dave Laube, “Limitations of CO2 cleaning for Semiconductor Process Tools”, A2C2

Magazine, February 2001, p. 9. (for general info on this article email:

[email protected]

)

26. Phil Danielson, “Contamination Lurks in Vacuum Systems, Sources”, R&D

Magazine, May 2001, p. 45.

27. Phil Danielson, “Fight Humidity in your vacuum system”, R&D Magazine, June

2001, p. 67.

28. Bob Langley and Paul LaMarche, “Cleaning of Parts For Use In Vacuum”, Vacuum

Technology and Coating, August 2001, p.6.

29. Phil Danielson, “Using Simple Tools to Avoid Vacuum Performance Problems”,

R&D Magazine, Dec 2001, p. 61. Note: This is an excellent explanation of how rate-
of-rise and pumpdown curves can be used to characterize vacuum systems. IGC100
controllers offer front panel display of such curves, making system characterization
very simple.

30. Donald M. Mattox, “Deposition Chambers and Vacuum-surface “Conditioning””,

Vac. Techn. & Coating, Sept. 2002, p. 30.

31. P. A. Redhead, “Recommended practices for measuring and reporting outgassing

data”, J. Vac. Sci. Technol. A 29(5)(2002)1667. Note: This is another Redhead
classic, this time recommending a set of uniform procedures for reporting outgassing
data.

«
...
334
335
336
337
338
...
»

Содержание RGA100











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RGA100

Бренд: Bacharach Страницы: 87

Бренд: National Instruments Страницы: 38

Бренд: Emos Страницы: 76

Бренд: Hanna Instruments Страницы: 52

Recordall Series

Бренд: Badger Meter Страницы: 8

Бренд: PCE Health and Fitness Страницы: 11

DT4120 PS Series

Бренд: Datcon Страницы: 92

Бренд: Velleman Страницы: 32

Бренд: LAUMAS Страницы: 12

Бренд: Roland Страницы: 32

Бренд: NIEUWKOOP Страницы: 2

Бренд: Hanna Instruments Страницы: 28

Бренд: TESTO Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: ATIM Страницы: 32

Бренд: Kobold Страницы: 27

Xevo TQ-XS Mass

Бренд: Waters Страницы: 213

ZET 7152-N-VER.3

Бренд: ZETLab Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды