Sony Ericsson W550c Скачать руководство пользователя

Страница: 17 / 128

Working Instruction

Mechanical

3/00021-1/FEA 209 544/594 B

Sony Ericsson Mobile Communications AB

17(128)

2.2.2

Outer Base Cover Installation

If this part is being replaced

, refer to the “Outer Base Cover” subsection under the “Parts

Replacement” portion of this document for detailed instructions on how to replace this part.

Tools needed:

•

Torque screwdriver

•

Torx Plus size 5 bit

•

Style 2A ESD tweezers (Blunt tip)

Step-by-Step Instructions

Rotate the inner base cover relative to the flip
portion of the phone so that the phone is in the open
position as shown.

NOTE! Verify that the two cables are not twisted

together.

Orient the outer base cover so that it is perpendicular
to the flip assembly with the system connector end of
the outer base cover towards the inner base cover
and the battery cavity adjacent to the inner base
cover’s keypad area.

NOTE! Use one hand to hold the phone in this

orientation.

NOTE! The cable assembly with the color mark

matches to the board connection that has the
large gold dot below it.

Содержание W550c

































































































































Результаты поиска

Содержание W550c

Отзывы:

Похожие инструкции для W550c

Бренды по названию

Популярные бренды

Sony Ericsson W550c, Руководство по эксплуатации, механическое

Результаты поиска

Содержание W550c

Отзывы:

Похожие инструкции для W550c

Бренды по названию

Популярные бренды