manualshive.com logo in svg

Solcon HRVS-DN series, Инструкция по эксплуатации

Поделиться
Скачать
Solcon HRVS-DN series Скачать руководство пользователя страница 8

8 • Safety & Warnings

 

_____________________________________________________________________________________________ 

 

2.

 

SAFETY & WARNINGS 

 

2.1

 

Safety 

 

1 

Read this manual carefully before operating the equipment and follow its 
instructions. 

2 

Installation, operation and maintenance should be in strict accordance 
with this manual, national codes and good practice. 

3 

Installation or operation not performed in strict accordance with these 
instructions will void manufacturer’s warranty. 

4 

Disconnect all power inputs before servicing the soft starter and/or the 
motor. 

5 

After installation, check and verify that no parts (bolts, washers, etc.) 
have fallen into the Power Section (IP00) of the HRVS-DN. 

 

2.2

 

Attention 

 

1 

This product was designed for compliance with IEC 60947-4-2 for class A 
equipment and EN 50178. 

2 

For further information, see the Technical Specifications. 

 

2.3

 

Warnings 

 
 
 
 
 
 
 

 

1 

Internal components and PCBs are at mains potential when the HRVS-
DN is connected to mains. This voltage is extremely dangerous and 
contact with it will cause death or severe injury. 

2 

When the HRVS-DN is connected to mains full voltage may appear on 
the HRVS-DN’s output terminals and motor’s terminals, 

even if control 

voltage is disconnected and motor is stopped

. 

3 

The HRVS-DN must be grounded to ensure correct operation, safety and 
to prevent damage. 

4 

Check that power factor capacitors are 

not

 connected to the output side 

of the HRVS-DN (U, V, W). 
Also make sure that power factor capacitors are not connected to the 
bypass preparation bus bars (L1B, L2B, L3B when exist) 

 

The company reserves the right to make any improvements or modifications to its products without 
prior notice. 

 

 

Содержание HRVS-DN series






















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды