manualshive.com logo in svg

Solcon HRVS-DN series, Инструкция по эксплуатации

Поделиться
Скачать
Solcon HRVS-DN series Скачать руководство пользователя страница 165

165 • HRVS-DN Communication (DeviceNet™) 

 

_______________________________________________________________________________________________ 

 

Figure 57 - Data rate (Baud rate) rotary switch layout 

Rotary switch S1 (BAUD) is used to select the DeviceNet Baud Rate. The valid range of baud rates is 1 
(125K), 2 (250K), 5 (500K), and P (programmable). All values P and above set the baud rate to the last baud 
rate the device was powered up at and allow software configuration tools to modify the baud rate. 
Factory default settings for the rotary switches are typically Address 63, 125K. 

18.1.6

 

LED Indicators 

The DeviceNet Gateway provides support for three LEDs: Serial Status (Modbus Diagnostic), Network 
Status, and Module Status. The LED on the right indicates the current Serial or Modbus Diagnostic status. 
The operation of the Modbus LED is described in Table 1. 

Table 1 

Modbus Diagnostic Status LED 

Color State 

Indication 

None Off 

No 

power 

Red Flashing 

Modbus 

Timeout 

Orange Flashing 

Modbus 

Error 

Green Flashing 

Normal 

operation 

 

The LED in the middle indicates the Network Status. The operation of the Network Status LED is described 
in Table 2. 

Table 2 

DeviceNet Network Status LED 

Color State 

Indication 

None Off No 

Power 

Red 

Solid Unrecoverable 

Fault 

Flashing 

Recoverable Fault 
I/O Connection Timed Out 

Green 

Solid 

Normal runtime operation 

Flashing 

Device is idle or not allocated 
to a master 

Red / Green 

Alternating 

Identify (Offline Connection 
Set) 

 

The LED on the left indicates the Module Status. The operation of the Module Status LED is described in 
Table 3. 

Table 3 

DeviceNet Module Status LED 

Color State 

Indication 

None Off  No 

Power 

Red 

Solid Unrecoverable 

Fault 

Flashing Recoverable 

Fault 

Green 

Solid Normal 

operation 

Flashing Not 

Used 

Red / Green 

Alternating 

Not used 

 

125Kb

250Kb

500Kb

PGM

DATA RATE

Содержание HRVS-DN series






















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды