manualshive.com logo in svg

Solcon HRVS-DN series, Инструкция по эксплуатации

Поделиться
Скачать
Solcon HRVS-DN series Скачать руководство пользователя страница 112

112 • Start Procedure for Medium voltage Motor 

 

_____________________________________________________________________________________________ 

 

13.

 

START PROCEDURE FOR MEDIUM VOLTAGE MOTOR 

13.1

 

Special Attention Notes 

Special 
Attention! 

 Make sure that you know where the Emergency stop button is located, so you 

can stop immediately if needed. 

 Verify that the Emergency stop button is operative and pushing the Emergency 

stop button disconnecting the motor from the mains. 

 During the entire starting time you should continuously read the three currents 

as shown on the HRVS-DN LCD display. They should show, more or less same 
values. 

 If the currents are significantly different - STOP IMMEDIATELY. Do not wait the 

total start time until a trip occurs. 

 Verify that NUMBER OF STARTS parameter is set to 1 and STARTS PERIOD 

is set to 20. 
Remember ! Do not start too often, especially if the starting time is long. 
Prevent damage to both motor and starter ! 

 Carefully read the Soft Starter Instruction Manual as well as the optional Motor 

Protection Relay (MPR) Instruction Manual if installed. 

  When mains voltage is connected to the HRVS-DN, even if control voltage is 

disconnected, full voltage appear on the HRVS-DN load terminals. Therefore, 
for isolation purposes, it is necessary to connect an isolating device upstream to 
the HRVS-DN.  

 Power factor correction capacitors must 

not

 be installed on the load side of the 

HRVS-DN. When required, install capacitors on the line side of the HRVS-DN. 

 Do not interchange line and load connections. Verify correct connections to the 

HRVS-DN terminals: L1, L2, L3, L1b, L2b, L3b, U, V, W. 

 Before starting the motor verify its rotation direction. If needed, disconnect the 

rotor from the mechanical load and verify the correct direction of rotation. 

 Prior to start up procedure, make sure that line voltage and control voltage 

match the ones shown on the label of the HRVS-DN. 

 When the Start signal is initiated and a motor is not connected to load terminals, 

the S. SCR OR WR. CON protection will be activated. Other loads such as 
incandescent light bulbs, resistors, etc. may also cause a S. SCR OR WR. CON 
fault. 

 

13.2

 

Prior to Commissioning in Medium Voltage 

Verify that the Full Load Ampere (FLA) of the motor is lower than or equal to the Full Load Current (FLC) of 
the HRVS-DN, and that the mains and control voltages are as indicated on the side and/or front label of the 
HRVS-DN. 

 

  Verify that HRVS-DN FLC 

≥

 motor FLA! 

 

  Verify that mains voltage is correct! 

 

  Verify that control voltage is correct! 

 

 

                

HRVS-DN label - example

 

 

 

 

Содержание HRVS-DN series






















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды