manualshive.com logo in svg

Solcon HRVS-DN series, Инструкция по эксплуатации

Поделиться
Скачать
Solcon HRVS-DN series Скачать руководство пользователя страница 131

131 • HRVS-DN Communication (ModBus Protocol) 

 

_______________________________________________________________________________________________ 

16.

 

HRVS-DN COMMUNICATION (MODBUS PROTOCOL) 

16.1

 

Introduction            

 
This document summarizes the Modbus serial link protocol to / from the Digital Soft Starter (HRVS-DN). The 
HRVS-DN can be equipped with many other serial link protocols. 

Features:

 

 
* RS485 

Hardware. 

*  

Asynchronous serial link. 

*  

Half duplex. 

*  

Format: 

Modbus RTU Mode

 (Remote Terminal Unit Mode). 

- Binary, 
- Each character contains 11 bits: 

- 1 start bit 
- 8 data bits, least significant bit sent first. 
- 1 Parity bit. Even / Odd / No can be selected. 
- 1 Stop bit if Parity is used, 2 stop bits if Parity is not used. 

- 

C

yclical 

R

edundancy 

C

heck (CRC), 16 bits.  

* 

Baud Rates: 1200 / 2400 / 4800 / 9600 bits per second. 

*  

Response time of the HRVS-DN:     

- Normally, 4ms <= time response <= 40mS . 
- For a long response, time response <= 200mS.  

* 

It is not recommended to transmit to the HRVS-DN, at a rate higher than once per second because this 
can slow down HRVS-DN response times. 

* 

After storing parameter settings, there is a 1 sec. time period during which transmission to the same 
HRVS-DN is forbidden. 

* 

Broadcast commands: not supported. 

 
 

Notes: 

 
* 

You must connect earth to the earth screw before connecting serial link wires. Ignoring this 
instruction may result in permanent damage to the Serial Link Hardware, and can be dangerous.

 

 
*   It is recommended that you connect 120 OHM resistors to both ends of the serial link. 
*  When the serial link is connected to Solcon's Serial Link Adapter you are not allowed to connect the 120 

OHM resistors. 

*  Turn off (and on again) power to the controller after changing Baud_Rate, Parity_Check or Serial_Link_No 

(Slave Address). These parameters can only be modified manually and not through the Serial Link. 
 

 

Содержание HRVS-DN series






















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды