Solcon HRVS-DN series Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 181

Solcon HRVS-DN series Скачать руководство пользователя страница 47

47 • Control Keypad

_______________________________________________________________________________________________

7.

CONTROL KEYPAD

The control keypad is the link between the HRVS-DN and the user.
The HRVS-DN control keypad features:

(1) Two lines of 16 alphanumeric characters each with selectable languages – English, French,

German, Spanish and Turkish. Russian and Chinese characters are optional and must be pre-
ordered.

(2) Six push-buttons (

Mode

,

Reset

,

Select

,

Store

, Up (

▲

) and down (

▼

) keys).

(3) Eight indication LEDs (

On, Start, Run, S.Stop, Stop, Test,, D.Adj., Fault

)

Figure 22 - HRVS-DN Control Keypad

7.1

LCD Arrangement

CURRENT LIMIT
390%

Upper line displays function.
Lower line displays setting and\or measured values.

7.2

Push-Buttons

Mode

Scrolls through the display and programming menus of the HRVS-DN.

Note

: Pressing

Mode

continuously increases the speed at which the parameters change.

Select

When a mode name is displayed, pressing this button drills down to the parameters for that
mode. When a parameter is displayed, pressing this button scrolls to the next parameter.

▲

Allows the operator to increment adjusted values shown in the display. Operator should press
this button once to increment one value, or continuously to rapidly increment values up to the
maximum value.

▼

Allows the operator to decrement adjusted values shown in the display. Operator should press
this button once to decrement one value, or continuously to rapidly decrement values up to the
minimum value.

Store

Stores modified parameters

only

when you have scrolled through all parameters and STORE

ENABLE XXXXXX PARAMETERS is displayed. After you store a parameter successfully DATA
SAVED OK message will display.

Note

: Pressing this button at any other time has no effect.

Reset

Resets the HRVS-DN after a fault has been dealt with

and

the start command has been removed

(except for UNDERCURR. TRIP – Refer to section

7.8.6 page 71 parameter UNDER CUR.

RESET). This cancels the fault displayed and allows you to restart the motor.

(3)

(1)

(2)

«
...
45
46
47
48
49
...
»

Содержание HRVS-DN series






















































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды