Simrad GO XSE Series Скачать руководство пользователя страница 82

Страница: 82 / 242

Turn variables:

•

Course change

•

Leg distance

Square

Steers the vessel in a square pattern, doing 90° course changes.
Turn variable:

•

Leg distance

S-turn

Makes the vessel yaw around the main heading. When activated,
the autopilot is switched to S-turns mode.
Turn variables:

•

Course change

•

Turn radius

Depth contour tracking

Makes the autopilot follow a depth contour.

Note:

DCT turn pattern is only available if the system has a valid

depth input.

Warning:

Do not use the DCT turn pattern unless the

seabed is suitable. Do not use it in rocky waters where
the depth is varying significantly over a small area.

Note:

If depth data is lost during DCT the autopilot will

automatically switch to auto mode.

Autopilot

| GO XSE/XSR Operator Manual

Содержание GO XSE Series



















































































































































































































































Результаты поиска

Содержание GO XSE Series

Отзывы:

Похожие инструкции для GO XSE Series

Бренды по названию

Популярные бренды

Simrad GO XSE Series, Руководство оператора

Результаты поиска

Содержание GO XSE Series

Отзывы:

Похожие инструкции для GO XSE Series

Бренды по названию

Популярные бренды