manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Rejecting radar interference

The Interference rejection (IR or Interf. rej.) option is used to
eliminate second trace echoes from far distance targets, and the
interference from radar units operating in the same frequency band.
When the IR is ON, transceiver pulse staggering is enabled. When
enabled, the transceiver PRF is changed slightly for each sweep. By
doing this, spiral interferences and second trace echoes are split in
range from sweep to sweep. The IR processing clears all the echoes
found at the same range if they are not present in each sweep.
The IR must be chosen according to the environment around own
ship:

•

IR off when the maximum signal from the receiver is needed

•

IR on when the interference or second trace echoes disturb the
radar image

To avoid missing weak targets, the interference rejection should be
set to OFF when no interference exists.

Target separation

Controls the target discrimination of the radar (separation between
objects is more prominent).

Fast scan

Sets the speed of the radar antenna rotation. This option gives faster
target updates.

Ú

Note: 

Maximum speed may not be achieved depending on the

radar Settings, Mode, and Range selected. The radar will only
rotate as fast as the current control settings allow.

Target boost

The target boost control increases pulse length or reduces radar
bandwidth to make targets appear larger in range and increase
radar sensitivity.

More options

Menu options can vary depending on your radar's capability.

Radar

 | GO XSE/XSR Operator Manual

125

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Tanco A Series Operator'S Handbook Manual preview
A Series
Бренд: Tanco Страницы: 72
HABYS Aero Instruction Manual & Warranty preview
Aero
Бренд: HABYS Страницы: 16
Acterna A Series Operating Manual preview
A Series
Бренд: Acterna Страницы: 72
GE ImageQuant LAS 4000 Original Instructions Manual preview
ImageQuant LAS 4000
Бренд: GE Страницы: 86
GE AKTApure Operating Instructions Manual preview
AKTApure
Бренд: GE Страницы: 160
GE AKTA avant Getting Started preview
AKTA avant
Бренд: GE Страницы: 134
Qazqa Movie FL Black E27 Flaps Instruction Manual preview
Movie FL Black E27 Flaps
Бренд: Qazqa Страницы: 2
ACCU-CHECK AVIVA COMBO Reference Manual preview
AVIVA COMBO
Бренд: ACCU-CHECK Страницы: 104
ACE INSTRUMENTS AFM-5 Quick Start Manual preview
AFM-5
Бренд: ACE INSTRUMENTS Страницы: 2
ODA LP Series User Manual preview
LP Series
Бренд: ODA Страницы: 103
Balluff BTL PA0400 Series Assembly Instructions Manual preview
BTL PA0400 Series
Бренд: Balluff Страницы: 22
Balluff Micropulse BTL5 Series Condensed Manual preview
Micropulse BTL5 Series
Бренд: Balluff Страницы: 12
Balluff BNI IOW-560-W01-K022 User Manual preview
BNI IOW-560-W01-K022
Бренд: Balluff Страницы: 32
Baltic MK5 User Manual preview
MK5
Бренд: Baltic Страницы: 68
Baltic 150N User Manual preview
150N
Бренд: Baltic Страницы: 68
Balmar Max Charge MC-612 Installation And Operator'S Manual preview
Max Charge MC-612
Бренд: Balmar Страницы: 12
Balluff BTL PA0400 Series User Manual preview
BTL PA0400 Series
Бренд: Balluff Страницы: 204
Banfer Vario Manual preview
Vario
Бренд: Banfer Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды