Simrad GO XSE Series Скачать руководство пользователя страница 90

Страница: 90 / 242

The autopilot will engage in the selected mode, and the autopilot
controller will change to show active mode options.
To disengage the autopilot:

•

Select the standby button

When the autopilot is in standby, the boat must be steered
manually.

Autopilot indication

The status bar shows autopilot information as long as an autopilot
computer is connected.

Autopilot modes

The autopilot has several steering modes.

Anchor modes

In these modes the trolling motor maintains the vessel position at a
selected location.

Note:

When in anchor mode, the vessel heading can be

affected by wind or current.

The following anchor options are available:

Cursor

Navigates to cursor position, and then maintains the vessel at that
position.

Trolling motor autopilot

| GO XSE/XSR Operator Manual

Содержание GO XSE Series



















































































































































































































































Результаты поиска

Содержание GO XSE Series

Отзывы:

Похожие инструкции для GO XSE Series

Бренды по названию

Популярные бренды

Simrad GO XSE Series, Руководство оператора

Результаты поиска

Содержание GO XSE Series

Отзывы:

Похожие инструкции для GO XSE Series

Бренды по названию

Популярные бренды