manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Main radar PPI

Radar overlay on a chart

Using the cursor on a radar panel

By default, the cursor is not shown on a radar panel.
When you position the cursor on the radar panel, the cursor
position window is activated.

The cursor assist function

Ú

Note: 

The cursor assist function is available if it is enabled. Refer

to 

"Customizing the long press feature"

 on page 26.

The cursor assist function allows for fine tuning and precision
placement of the cursor without covering details with your finger.
Activate the cursor on the panel, then press and hold your finger on
the screen to switch the cursor symbol to a selection circle,
appearing above your finger.
Without removing your finger from the screen, drag the selection
circle to the desired position.
When you remove your finger from the screen the cursor reverts to
normal cursor operation.

Go to cursor

You can navigate to a selected position on the image by positioning
the cursor on the panel, and then using the go to cursor menu
option.

New waypoint

You can save a new waypoint at a selected position by positioning
the cursor on the panel, and then using the new waypoint menu
option.

112

Radar

 | GO XSE/XSR Operator Manual

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

DARKSTAR TECHNOLOGIES D340 Manual To Operation preview
D340
Бренд: DARKSTAR TECHNOLOGIES Страницы: 4
TDW D2000 Maintenance Manuallines preview
D2000
Бренд: TDW Страницы: 2
Taurus 1170 Assembly And Operating Instructions Manual preview
1170
Бренд: Taurus Страницы: 25
Vancare G Series Quick Reference Manual preview
G Series
Бренд: Vancare Страницы: 3
Paitec ES-2000 User Manual preview
ES-2000
Бренд: Paitec Страницы: 14
C.M.O FL Series Instruction And Maintenance Manual preview
FL Series
Бренд: C.M.O Страницы: 10
ParaBody 875 Assembly Instruction Sheet preview
875
Бренд: ParaBody Страницы: 5
Baileigh Industrial TN-300 Operator'S Manual preview
TN-300
Бренд: Baileigh Industrial Страницы: 28
Baileigh Industrial BP-3305CNC Operator'S Manual preview
BP-3305CNC
Бренд: Baileigh Industrial Страницы: 56
Barreto 20RTK Operator'S Manual preview
20RTK
Бренд: Barreto Страницы: 20
Barreto 13STKH Owner'S Manual preview
13STKH
Бренд: Barreto Страницы: 18
Backyard Discovery Premier Series Manual preview
Premier Series
Бренд: Backyard Discovery Страницы: 41
Cambridge Audio azur 640H Important Information preview
azur 640H
Бренд: Cambridge Audio Страницы: 2
Quanser Aero 2 User Manual preview
Aero 2
Бренд: Quanser Страницы: 12
CAIRE FreeStyle Comfort Technical Manual preview
FreeStyle Comfort
Бренд: CAIRE Страницы: 33
Garmin GHC 10 Quick Start Manual preview
GHC 10
Бренд: Garmin Страницы: 20
Haag-Streit BM 900 Instructions For Use Manual preview
BM 900
Бренд: Haag-Streit Страницы: 16
Raymarine ST60+ SPEED INSTRUMENT Owner'S Handbook Manual preview
ST60+ SPEED INSTRUMENT
Бренд: Raymarine Страницы: 60

Бренды по названию

Популярные бренды

Загрузить еще бренды