manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Time plots

The system can present data history in different plots. The plots can
be displayed in full page, or combined with other panels.

The Time plot panel

The Time plot panel consists of two predefined layouts. You switch
between the layouts by selecting the left and right panel arrows.
You can also select the layout from the menu.
You can select which data to present on a time plot panel, and you
can define the time range for each plot.

Layout 1

Layout 2

Missing data

If the data is unavailable, the relevant plot turns into a dashed line
and flattens out at the point the data was lost. When the data
becomes available again, a dashed line joins up the two points
showing an average trend line bridging the missing data.

Missing data

If the data is unavailable, the relevant plot turns into a dashed line
and flattens out at the point the data was lost. When the data
becomes available again, a dashed line joins up the two points
showing an average trend line bridging the missing data.

Selecting data

Each data field can be changed to show the preferred data type and
the time range.

1.

Select the edit option from the menu

2.

Activate the field you want to edit

3.

Change the information type and eventually the range

4.

Save your changes

21 

196

Time plots

 | GO XSE/XSR Operator Manual

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

XAG P30 Quick Start Manual preview
P30
Бренд: XAG Страницы: 24
Cambro Camshelving Quick Start Manual preview
Camshelving
Бренд: Cambro Страницы: 6
Hach MET ONE 3400 Series User Manual preview
MET ONE 3400 Series
Бренд: Hach Страницы: 48
SAMCHULLY HCH Instruction Manual preview
HCH
Бренд: SAMCHULLY Страницы: 48
HAGER WERKEN SPEEDO-CLEAN Instructions For Use preview
SPEEDO-CLEAN
Бренд: HAGER WERKEN Страницы: 2
VelociRAX Light Bar Instruction Manual preview
Light Bar
Бренд: VelociRAX Страницы: 4
ABM Katana User Manual preview
Katana
Бренд: ABM Страницы: 17
RainPoint ITV105 User Manual preview
ITV105
Бренд: RainPoint Страницы: 40
FARM-MAXX FTL Series Operator'S Manual preview
FTL Series
Бренд: FARM-MAXX Страницы: 35
Össur bionic power knee Quick Reference Card preview
bionic power knee
Бренд: Össur Страницы: 2
Össur BALANCE KNEE OM8 Instructions For Use Manual preview
BALANCE KNEE OM8
Бренд: Össur Страницы: 36
Össur BALANCE FOOT J Instructions For Use Manual preview
BALANCE FOOT J
Бренд: Össur Страницы: 37
Össur REBOUND DIABETIC WALKER Instructions For Use Manual preview
REBOUND DIABETIC WALKER
Бренд: Össur Страницы: 63
Össur UNITY Instructions For Use Manual preview
UNITY
Бренд: Össur Страницы: 67
Électronique du Mazet ECHODIA Babyscreen Instructions For Use And Technical Description preview
ECHODIA Babyscreen
Бренд: Électronique du Mazet Страницы: 65
GRAU Team Agile Color Tune TM16-0 User Manual preview
Team Agile Color Tune TM16-0
Бренд: GRAU Страницы: 24
Bayer HealthCare Certegra Operation Manual preview
Certegra
Бренд: Bayer HealthCare Страницы: 104
Energizer EDC2-1001-RGB-MWT Quick Start Manual preview
EDC2-1001-RGB-MWT
Бренд: Energizer Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды