manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Introduction

Front controls

2

1

1

Touch screen

2

Power key

Press and hold to turn the unit ON/OFF.
Press once to display the System Controls dialog.

Card reader

Used for inserting a microSD memory card. The memory card can
be used for detailed chart data, software updates, transfer of user
data, and system backup.

Ú

Note: 

Do not download, transfer or copy files to a chart card.

Doing so can damage chart information on the chart card.

The card reader door is opened by pulling the rubber cover open.
The card reader door should always be securely shut immediately
after inserting or removing a card, in order to prevent possible water
ingress.

1 

Introduction

 | GO XSE/XSR Operator Manual

17

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Eazyzap Y724 Instruction Manual preview
Y724
Бренд: Eazyzap Страницы: 32
Obdstar MS50 User Manual preview
MS50
Бренд: Obdstar Страницы: 42
RayLight HERA Technical Document preview
HERA
Бренд: RayLight Страницы: 34
Gazelle GAZELLE FREESTYLE User Manual preview
GAZELLE FREESTYLE
Бренд: Gazelle Страницы: 10
Latham ECLIPSE Installation Manual preview
ECLIPSE
Бренд: Latham Страницы: 19
Hagerman ECHO Manual preview
ECHO
Бренд: Hagerman Страницы: 4
hager EK087 Manual preview
EK087
Бренд: hager Страницы: 2
Ampro TECSHOW QUAD SPIDER 60 User Manual preview
TECSHOW QUAD SPIDER 60
Бренд: Ampro Страницы: 9
HABYS Agila 2 Instruction Manual preview
Agila 2
Бренд: HABYS Страницы: 16
Panta Safe Light Solar Quick Start Manual preview
Solar
Бренд: Panta Safe Light Страницы: 2
Calrec OMEGA Installation Manual preview
OMEGA
Бренд: Calrec Страницы: 70
Raytheon V300 Instruction Manual preview
V300
Бренд: Raytheon Страницы: 68
KegLand Cannular Instruction Manual preview
Cannular
Бренд: KegLand Страницы: 23
Zero 88 Betapack 4 User Manual preview
Betapack 4
Бренд: Zero 88 Страницы: 12
Zest4Leisure Horizon Arch Instructions preview
Horizon Arch
Бренд: Zest4Leisure Страницы: 4
Zeiss ATLAS 9000 Service Manual preview
ATLAS 9000
Бренд: Zeiss Страницы: 119
Zehnder Rittling ComfoFond-L Installation Manual preview
ComfoFond-L
Бренд: Zehnder Rittling Страницы: 32
Cablexpert NCT-2 User Manual preview
NCT-2
Бренд: Cablexpert Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды