Simrad GO XSE Series Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 242

background image

You can set the length of the trails. The length represents the time it
takes for the trails to fade out. You can also turn OFF target trails.

Clear trails

The clear trails option clears target trails from your radar panel
temporarily. The trails start to build up again unless you switch the
function off.

EBL/VRM markers

The electronic bearing line (EBL) and variable range marker (VRM)
allows quick measurements of range and bearing to vessels and
landmasses within radar range. Two different EBL/VRMs can be
placed on the radar image.
The EBL/VRMs are by default positioned from the center of the
vessel. It is, however, possible to offset the reference point to any
selected position on the radar image.

Defining an EBL/VRM marker

1.

Ensure that the cursor is not active.

2.

Activate the More menu, select EBL/VRM, and then select
EBL/VRM 1 or EBL/VRM 2.

The EBL/VRM is now positioned on the radar image.

3.

Select the adjustment option from the menu if you need to
reposition the marker.

4.

Adjust the marker by dragging it into position.

5.

Save your settings.

Radar

| GO XSE/XSR Operator Manual

131

«
...
129
130
131
132
133
...
»

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: 3M Страницы: 2

Бренд: Kärcher Страницы: 88

Бренд: U-Line Страницы: 3

Бренд: U-Line Страницы: 2

Бренд: Yamaha Страницы: 48

Бренд: Sanav Страницы: 34

Бренд: Kärcher Страницы: 148

Бренд: Ublox Страницы: 22

Бренд: RAM Страницы: 4

MIDORI ULB-50sc

Бренд: Ushio Страницы: 24

Бренд: Kobelt Страницы: 20

Бренд: Pottinger Страницы: 39

Бренд: WAGNER Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды