manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Purging user data

Deleted user data are stored in the unit's memory until the data is
purged. If you have numerous deleted, unpurged user data, purging
may improve the performance of your system.

Ú

Note: 

When user data is deleted and/or purged from the

memory, it cannot be recovered.

Exporting the settings database

Use the settings database option in the storage dialog to export
your user settings.

Import system settings

 Warning: 

Importing system settings overwrites all

existing system settings.

1

Connect a storage device to the unit

226

Maintenance

 | GO XSE/XSR Operator Manual

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

GE TruSat User Manual preview
TruSat
Бренд: GE Страницы: 43
GE Responder AED Service Manual preview
Responder AED
Бренд: GE Страницы: 37
GE Senographe DS Operator'S Manual preview
Senographe DS
Бренд: GE Страницы: 210
GE MAC 5000 Field Service Manual preview
MAC 5000
Бренд: GE Страницы: 160
GE MAC 1600 Service Manual preview
MAC 1600
Бренд: GE Страницы: 146
GE Dash 2500 Quick Manual preview
Dash 2500
Бренд: GE Страницы: 6
GE ApexPro Manual preview
ApexPro
Бренд: GE Страницы: 27
GE Voluson 730 Manual preview
Voluson 730
Бренд: GE Страницы: 4
Datavideo HS-600 Instruction Manual preview
HS-600
Бренд: Datavideo Страницы: 50
Waterous Eclipse Installation, Operation And Maintenance Manual preview
Eclipse
Бренд: Waterous Страницы: 90
Campbell SC105 Product Manual preview
SC105
Бренд: Campbell Страницы: 14
Makita BBX7600N Parts Breakdown preview
BBX7600N
Бренд: Makita Страницы: 17
Makita BBX7600 Catalog preview
BBX7600
Бренд: Makita Страницы: 13
Garmin GMR 18 Installation Manual preview
GMR 18
Бренд: Garmin Страницы: 2
Garelick 71095 Mounting And Operating Instructions preview
71095
Бренд: Garelick Страницы: 4
Hakko Electronics 192 Instruction Manual preview
192
Бренд: Hakko Electronics Страницы: 8
Hailo Professional HS 8 Assembly And Operation preview
Professional HS 8
Бренд: Hailo Страницы: 5
Hainbuch TESTit Installation Manual preview
TESTit
Бренд: Hainbuch Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды