Simrad GO XSE Series Скачать руководство пользователя страница 208

Страница: 208 / 242

Using your phone with the MFD

About phone integration

The following functions are available when connecting a phone to
the unit:

•

read and send text messages

•

view caller ID for incoming calls

Note:

It is possible to use a smartphone to remotely control the

MFD. See

"Remote control of the MFD"

on page 205.

iPhone limitations:

•

only incoming calls and messages received while the phone is
connected to the MFD are available

•

messages cannot be sent from the MFD. iPhone does not
support sending messages from connected Bluetooth devices.

Connecting and pairing a phone

Note:

Bluetooth must be enabled on your phone before you

can connect to the MFD.

Note:

If you want to pair a phone while another phone is

connected to the MFD, see

"Managing Bluetooth devices"

on page 211.

Note:

You must always connect to a phone from the MFD, not

the other way around.

Use the phone icon in the toolbar to connect your phone to the
MFD. When the icon is selected the following happens:

•

Bluetooth is turned ON in the MFD

•

the Bluetooth dialog opens, listing all Bluetooth enabled devices
within range

To pair a phone listed as

other devices

in the dialog:

208

Using your phone with the MFD

| GO XSE/XSR Operator

Manual

Содержание GO XSE Series



















































































































































































































































Результаты поиска

Содержание GO XSE Series

Отзывы:

Похожие инструкции для GO XSE Series

Бренды по названию

Популярные бренды

Simrad GO XSE Series, Руководство оператора

Результаты поиска

Содержание GO XSE Series

Отзывы:

Похожие инструкции для GO XSE Series

Бренды по названию

Популярные бренды