manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Remote control of the MFD

Remote control options

The following options are available for remotely controlling your
MFD:

•

a smartphone or a tablet, connected to the same WiFi hotspot as
the MFD(s)

•

a smartphone or a tablet, connected to an MFD acting as a WiFi
access point

Ú

Note: 

For safety reasons, some functions cannot be controlled

from a remote unit.

Smartphones and tablets

The Link app

The Link app must be used to connect a phone or tablet to the
MFD.
When connected, the Link app on the phone or tablet can be used
to:

•

Remotely view and control the system

•

Back-up and restore settings

•

Back-up and restore waypoints, routes and tracks

The Link app can be downloaded from the relevant phone/tablet
application store.

Connecting via a hotspot

If you connect a phone/tablet and the MFD(s) to the same hotspot,
you can use your phone/tablet to control all MFDs on the same
network.

24 

Remote control of the MFD

 | GO XSE/XSR Operator Manual

205

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

CAMPAGNOLA HERCULES Quick Manual preview
HERCULES
Бренд: CAMPAGNOLA Страницы: 4
Kawai CS11 Setting Manual preview
CS11
Бренд: Kawai Страницы: 10
Mainca RC-100 Manual preview
RC-100
Бренд: Mainca Страницы: 21
Daktronics HS-200 Owner'S Manual preview
HS-200
Бренд: Daktronics Страницы: 30
DAKOTA ULTRASONICS PR-82 Operation Manual preview
PR-82
Бренд: DAKOTA ULTRASONICS Страницы: 28
Raymarine H6 System Installation Manual preview
H6
Бренд: Raymarine Страницы: 124
Raymarine H6 Owner'S Manual preview
H6
Бренд: Raymarine Страницы: 192
Nektar Panorama P1 User Manual preview
Panorama P1
Бренд: Nektar Страницы: 12
Taylor C712 Operator Training preview
C712
Бренд: Taylor Страницы: 41
Abus FUSG50101 Quick Manual preview
FUSG50101
Бренд: Abus Страницы: 12
RAMVAC BADGER LF2 User Manual preview
BADGER LF2
Бренд: RAMVAC Страницы: 53
Garmin Tacx Boost Bundle User Manual preview
Tacx Boost Bundle
Бренд: Garmin Страницы: 12
Garland SHAKER KEEPER 20V 200 Instruction Manual preview
SHAKER KEEPER 20V 200
Бренд: Garland Страницы: 84
OMGA TR 2B INC INT NC Operation And Maintenance Manual preview
TR 2B INC INT NC
Бренд: OMGA Страницы: 76
Cooper IB520081ML Installation Instructions Manual preview
IB520081ML
Бренд: Cooper Страницы: 10
Korg HT-10 Owner'S Manual preview
HT-10
Бренд: Korg Страницы: 32
DALBO MAXIDISC 300 Operator'S Manual preview
MAXIDISC 300
Бренд: DALBO Страницы: 27
Coemar Infinity Wash XL Instruction Manual preview
Infinity Wash XL
Бренд: Coemar Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды