manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Icon

Description

Pan to position a chart or sonar image on the
panel.

Pinch to zoom out on the chart or on an image.

Ú

Note: 

Not available for zooming sonar images.

Spread to zoom in on the chart or on an image.

Ú

Note: 

Not available for zooming sonar images.

Status bar icon definitions

Depending on your system and set up, the following icons can
appear on the status bar:

Icon

Definition

Alarm - a standard (yellow), important (orange) or
critical (red) alarm is sent. To remove the icon in the
status bar, acknowledge the alarm in the Alarms
dialog. If needed, change the alarm setting or
remedy the situation so the same alarm is not resent
immediately by the system.

Autopilot modes: Auto-Heading hold, Follow up,
Navigation, No drift, Standby. Use the autopilot
controller to select an autopilot mode.

Appendix

 | GO XSE/XSR Operator Manual

237

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

zipwake E Series Operator'S Quick Manual preview
E Series
Бренд: zipwake Страницы: 2
zipwake E Series Start-Up Checklist preview
E Series
Бренд: zipwake Страницы: 2
GE Ettan IPGphor 3 Instrument User Manual preview
Ettan IPGphor 3
Бренд: GE Страницы: 64
GE AMX 4+ Technical Publications preview
AMX 4+
Бренд: GE Страницы: 56
GE AMX 4+ Technical Manual preview
AMX 4+
Бренд: GE Страницы: 132
GE AKTAprocess Site Preparation Manual preview
AKTAprocess
Бренд: GE Страницы: 16
GE Logiq 500 Advanced Reference Manual preview
Logiq 500
Бренд: GE Страницы: 474
IDEAL Networks LanTEK IV User Manua preview
LanTEK IV
Бренд: IDEAL Networks Страницы: 60
IceCure IceSense3 User Manual preview
IceSense3
Бренд: IceCure Страницы: 104
TC Electronic M-ONE Quick Manual preview
M-ONE
Бренд: TC Electronic Страницы: 4
TC Electronic VORTEX MINI Quick Start Manual preview
VORTEX MINI
Бренд: TC Electronic Страницы: 6
TC-Helicon SINGTHING User Manual preview
SINGTHING
Бренд: TC-Helicon Страницы: 12
TC Electronic DB6 Manual preview
DB6
Бренд: TC Electronic Страницы: 76
Ultraflex A97 Installation And Maintenance Manual preview
A97
Бренд: Ultraflex Страницы: 48
GE Venue 50 Basic Service Manual preview
Venue 50
Бренд: GE Страницы: 289
Abus TAS 112 Installation And Operating Instructions Manual preview
TAS 112
Бренд: Abus Страницы: 8
Cuisinart GRMC3E Original Instructions Manual preview
GRMC3E
Бренд: Cuisinart Страницы: 159
Power Dynamics DJ Laptop stand +tray Instruction Manual preview
DJ Laptop stand +tray
Бренд: Power Dynamics Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды