manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

ForwardScan

About ForwardScan

ForwardScan sonar is a navigational aid that helps you monitor the
underwater environment in front of your vessel while carrying out
slow speed maneuvers.
To use the ForwardScan feature you must have a ForwardScan
transducer mounted on your vessel.
The ForwardScan transducer must be connected to a compatible
sonar module (or another unit which has built-in sonar shared over
the network).

 Warning: 

Do not rely on this equipment as your

principle source of navigation or hazard detection.

 Warning: 

Do not use this equipment to gauge depth

or other conditions for swimming or diving.

The ForwardScan image

A

Depth range scale and vessel position

B

Forward range scale

C

Point data

17 

172

ForwardScan

 | GO XSE/XSR Operator Manual

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

ZOLL R Series In-Service Manual preview
R Series
Бренд: ZOLL Страницы: 5
Accu-Chek Compact Pocket User Manual preview
Compact
Бренд: Accu-Chek Страницы: 3
iBin Compact Installation Instructions preview
Compact
Бренд: iBin Страницы: 2
BACtrack S75 Owner'S Manual preview
S75
Бренд: BACtrack Страницы: 13
TA Instruments DHR Series Getting Started Manual preview
DHR Series
Бренд: TA Instruments Страницы: 35
Baker D30R User Manual preview
D30R
Бренд: Baker Страницы: 82
Gatekeeper ITSS Installation Manual preview
ITSS
Бренд: Gatekeeper Страницы: 8
Gate Bure Rise & Go DB 56-309 Technical Manual preview
Bure Rise & Go DB 56-309
Бренд: Gate Страницы: 8
MAHA MBT Series Operating Instructions Manual preview
MBT Series
Бренд: MAHA Страницы: 21
MAGUIRE PRS-20 Installation Operation & Maintenance preview
PRS-20
Бренд: MAGUIRE Страницы: 47
Uniden HH940 Manual De Usuario preview
HH940
Бренд: Uniden Страницы: 23
Yamaha mLAN16E Software Manual preview
mLAN16E
Бренд: Yamaha Страницы: 126
Yamaha DM 2000 Version 2 Orientation Manual preview
DM 2000 Version 2
Бренд: Yamaha Страницы: 8
Cannon MAGNUM 5 Owner'S Manual preview
MAGNUM 5
Бренд: Cannon Страницы: 70
Sakai 544 Troubleshooting And Diagnostics Information preview
544
Бренд: Sakai Страницы: 31
+GF+ COOL-FIT 2.0 Assembly Instructions preview
COOL-FIT 2.0
Бренд: +GF+ Страницы: 2
Össur Unity for Pro-Flex Pivot Instructions For Use Manual preview
Unity for Pro-Flex Pivot
Бренд: Össur Страницы: 40
Össur ICELOCK 234 LANYARD Instructions For Use Manual preview
ICELOCK 234 LANYARD
Бренд: Össur Страницы: 94

Бренды по названию

Популярные бренды

Загрузить еще бренды