manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Service report

The system has a built-in service assistant that creates a report
about the unit. The service report is used to assist in technical
support enquiries.
It can also include information about devices connected to the
network(s).
The report includes the software version, serial number, and
information from the settings file.
If you call technical support before creating the report, you can
enter an incident number to assist with tracking. You can attach
screenshots and log files to the report.

Ú

Note: 

There is a 20MB limit for the report attachments.

The report can be saved to a storage device and emailed to support.
You can also upload it directly if you have an internet connection.

Maintenance

 | GO XSE/XSR Operator Manual

223

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Raytheon V700 Instruction Manual preview
V700
Бренд: Raytheon Страницы: 69
Galaxy Audio RM2 Operation Manual preview
RM2
Бренд: Galaxy Audio Страницы: 24
NEC MD462OR Quick Reference Manual preview
MD462OR
Бренд: NEC Страницы: 44
Baileigh Industrial 1000568 Operator'S Manual preview
1000568
Бренд: Baileigh Industrial Страницы: 40
Abbott CentriMag Quick Reference Manual preview
CentriMag
Бренд: Abbott Страницы: 2
Abbott FreeStyle Libre Software Update preview
FreeStyle Libre
Бренд: Abbott Страницы: 3
abc PHASER Operation And Maintenance Manual preview
PHASER
Бренд: abc Страницы: 8
Datex-Ohmeda S/5 Aespire User'S Reference Manual preview
S/5 Aespire
Бренд: Datex-Ohmeda Страницы: 80
MacDon D65 Quick Start Manual preview
D65
Бренд: MacDon Страницы: 2
V-TAC 7817 Installation Instruction preview
7817
Бренд: V-TAC Страницы: 6
DBX Bushido DR1 Manual preview
DR1
Бренд: DBX Bushido Страницы: 12
Gaspardo SP SPRINT Manual preview
SP SPRINT
Бренд: Gaspardo Страницы: 16
Gastrodomus PH100 Installation, Operating And Service Instructions preview
PH100
Бренд: Gastrodomus Страницы: 4
HANYOUNG NUX HL Series Instruction Manual preview
HL Series
Бренд: HANYOUNG NUX Страницы: 2
Gastrodomus CL Instructions For Use And Maintenance Manual preview
CL
Бренд: Gastrodomus Страницы: 39
Halyard MIC-KEY Instructions For Use Manual preview
MIC-KEY
Бренд: Halyard Страницы: 88
HALDER EH 2B353 Short Instruction Manual preview
EH 2B353
Бренд: HALDER Страницы: 2
Hällde RG-200 User Instructions preview
RG-200
Бренд: Hällde Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды