manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

•

Un-select the devices that are to be removed from the control
bar.

•

Select None to remove all CZone devices from the control bar.

Multiple switching devices can be connected to the network. When
you select to display more than the maximum of devices allowed at
a time, a message informs you the maximum has been reached.

CZone digital switching control bar

If configured and setup properly, the CZone digital switching device
can be operated from the control bar.

Control bar buttons

The button indicates the status of the switch.

Off (black)
The switch is OFF.
On (blue)
The switch is ON.
Error (red)
There is a switch or communication error.

Integration of 3 party devices

 | GO XSE/XSR Operator Manual

231

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Unex UD-211-002-200 Operating Manual preview
UD-211-002-200
Бренд: Unex Страницы: 5
Dairyland SSD Operation Manual preview
SSD
Бренд: Dairyland Страницы: 21
Garmin GNX Wind Owner'S Manual preview
GNX Wind
Бренд: Garmin Страницы: 10
Garmin GMR 404 Owner'S Manual preview
GMR 404
Бренд: Garmin Страницы: 26
Naviom AIS Installation Instructions Manual preview
AIS
Бренд: Naviom Страницы: 31
Hammer Strength MTSP Unpacking And Assembly Instructions preview
MTSP
Бренд: Hammer Strength Страницы: 18
Pace ThermoTweez Handpiece TT-65 Operation & Maintenance Instructions Manual preview
ThermoTweez Handpiece TT-65
Бренд: Pace Страницы: 14
Rational iCombi Pro Original Installation Manual preview
iCombi Pro
Бренд: Rational Страницы: 16
Tanaka APM-7 Instruction Manual preview
APM-7
Бренд: Tanaka Страницы: 20
Tandem AutoSoft 90 Indications For Use preview
AutoSoft 90
Бренд: Tandem Страницы: 80
Tanco E100 SA Quick Reference Manual preview
E100 SA
Бренд: Tanco Страницы: 4
Wasp Clay Kit Original Instructions Manual preview
Clay Kit
Бренд: Wasp Страницы: 50
Gaspardo PI Use And Maintenance preview
PI
Бренд: Gaspardo Страницы: 44
Sable 30K Directions For Use Manual preview
30K
Бренд: Sable Страницы: 28
ubicquia 3i Installation Manual preview
3i
Бренд: ubicquia Страницы: 4
Petzl P51A Technical Notice preview
P51A
Бренд: Petzl Страницы: 15
Lites PROFILE C5 Owner'S And Service Manual preview
PROFILE C5
Бренд: Lites Страницы: 8
Taylor 8664 Service Manual preview
8664
Бренд: Taylor Страницы: 82

Бренды по названию

Популярные бренды

Загрузить еще бренды