manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Watching targets

Use this option to help you follow specific targets on the radar
image.
Select a target, then select the Watch target option. The target
becomes highlighted. Repeat the process to watch another target.
Multiple targets can be watched.

Stop watching targets

You can stop watching targets which no longer need special
attention.
To stop watching specific targets, select a watched target on the
radar image, then the Stop watching option. The stop watching
option is available in the menu while a watched target is selected.

Select the stop watching all option to stop watching all the
watched targets. The stop watching all option is available when
targets are being watched and while the cursor is cleared from the
radar image.

Radar target symbols

The system uses the target symbols shown below.

Radar target, not moving.

11

Tracked radar target, not moving. Tracked radar
targets have a ring around them. They also show the
target ID number.

5

Tracked radar moving target with trail when target
history is enabled. Shows the tracked target ring and
the target ID number.

2

Tracked moving radar target with no course
extension (short line indicating the direction where
the target moves). Shows the tracked target ring and
the target ID number.

Radar

 | GO XSE/XSR Operator Manual

119

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

C.M.O FL Series Instruction And Maintenance Manual preview
FL Series
Бренд: C.M.O Страницы: 10
Bahco BH6 Service Manual preview
BH6
Бренд: Bahco Страницы: 9
Eaton SafeLite Mounting And Operating Instructions preview
SafeLite
Бренд: Eaton Страницы: 16
Eaton EMS-2 Instruction Leaflet preview
EMS-2
Бренд: Eaton Страницы: 6
Ecco 21 Series Installation Instructions Manual preview
21 Series
Бренд: Ecco Страницы: 17
Tanco 1300 Series Operator'S Handbook Manual preview
1300 Series
Бренд: Tanco Страницы: 112
Qiagen TissueLyser II User Manual preview
TissueLyser II
Бренд: Qiagen Страницы: 48
Qiagen QIAcube User Manual preview
QIAcube
Бренд: Qiagen Страницы: 162
Qazqa 44083 Manual preview
44083
Бренд: Qazqa Страницы: 4
Qlightec QWCD35 Instructions Manual preview
QWCD35
Бренд: Qlightec Страницы: 12
WalkMed 350VL Quick Reference preview
350VL
Бренд: WalkMed Страницы: 2
Walinga Central Vac Installation Manual preview
Central Vac
Бренд: Walinga Страницы: 20
Fast RH15 Owner'S Manual preview
RH15
Бренд: Fast Страницы: 60
Japan Radio Co. JMA-5212-4 Field Service Manual preview
JMA-5212-4
Бренд: Japan Radio Co. Страницы: 20
ABB VM3D Operating Instruction preview
VM3D
Бренд: ABB Страницы: 4
Dantel 44210 Installation & Operation Manual preview
44210
Бренд: Dantel Страницы: 22
Össur RE-FLEX SHOCK Instructions For Use Manual preview
RE-FLEX SHOCK
Бренд: Össur Страницы: 50
Össur PROPRIO FOOT Instructions For Use Manual preview
PROPRIO FOOT
Бренд: Össur Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды