manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Dangerous target alerts

When a vessel meets the dangerous target criteria set in the Vessels
and tracked targets dialog (TCPA/CPA settings) and if the
Dangerous target alert option in the Alarms settings dialog is
enabled, a dangerous target alert message dialog is displayed. The
following options are available in the message dialog:

•

Disable

, closes the message dialog and cancels the dangerous

target alert for all vessels. You can re-enable the dangerous vessel
alert in the Vessels section of the Alarms settings dialog.

Ú

Note: 

When Disable is selected, the Dangerous target alert

option in the Alarms settings dialog is turned off. When the
Dangerous target alert option is turned off (disabled),
dangerous target alert messages are not generated for either
radar or AIS dangerous targets.

•

Ignore

, closes the message dialog and disables the alert for that

vessel. The alert for that vessel will reappear if the status of that
vessel changes, i.e. that vessel becomes safe and then dangerous
again.

•

View

, closes the message dialog and opens the chart panel with

the dangerous vessel’s pop-up activated. You can select the
vessel’s pop-up in the chart panel to see the AIS vessel details.

AIS target symbols and icons

Symbol

Description

AIS target, stationary or moving if no extension lines
enabled

AIS dangerous target (yellow). The yellow color is
shown when the radar palette is black/red or black/
green.

AIS dangerous target (purple). The purple color is
shown when the radar palette is white/red.

AIS dangerous target (red). The red color is shown
when the radar palette is black/yellow.

AIS

 | GO XSE/XSR Operator Manual

141

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Odom ES3 Hardware Configuration preview
ES3
Бренд: Odom Страницы: 19
MacDon M205 Installation Instructions Manual preview
M205
Бренд: MacDon Страницы: 30
Raven SC1 Accessory Installation Manual preview
SC1
Бренд: Raven Страницы: 27
Raven SC1 Calibration And Operation Manual preview
SC1
Бренд: Raven Страницы: 79
Raven SC1 Calibration & Operation Manual preview
SC1
Бренд: Raven Страницы: 88
Raymarine RS232 Owner'S Handbook Manual preview
RS232
Бренд: Raymarine Страницы: 24
Hansen P4 Installation Manual preview
P4
Бренд: Hansen Страницы: 72
AAT SOLO Original User Manual preview
SOLO
Бренд: AAT Страницы: 16
AAT S-max Translation Of The Original User Manual preview
S-max
Бренд: AAT Страницы: 40
Dairy Tech Platinum Series Operator'S Manual preview
Platinum Series
Бренд: Dairy Tech Страницы: 38
H&S M6 Parts List And Operator'S Instructions preview
M6
Бренд: H&S Страницы: 34
QAL Medical 480 Service And Technical Manual preview
480
Бренд: QAL Medical Страницы: 42
Nitecore NPL20 User Manual preview
NPL20
Бренд: Nitecore Страницы: 4
Jeio tech Lab companion SI-300 Operating Instruction preview
Lab companion SI-300
Бренд: Jeio tech Страницы: 69
JDS Uniphase IP Video Test Option HST-3000 Product Manual preview
IP Video Test Option HST-3000
Бренд: JDS Uniphase Страницы: 4
Jct JH Series Operating Manual preview
JH Series
Бренд: Jct Страницы: 16
Yamaha MU100 Manuel Du Propriétaire preview
MU100
Бренд: Yamaha Страницы: 178
Yamaha EMT-10 Manuel De L'Utilisateur preview
EMT-10
Бренд: Yamaha Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды