Simrad GO XSE Series Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 242

background image

E

Bearing line with allowed off course limit

When travelling on a route, the bearing line shows the
intended course from one waypoint towards the next.
When navigating towards a waypoint (cursor position, MOB
or an entered lat/lon position), the bearing line shows the
intended course from the point at which navigation was
started towards the waypoint.

F

XTE limit

If the XTE (Cross Track Error) exceeds the defined XTE limit,
this is indicated with a red arrow including the distance
from the track line. Refer to

G Vessel symbol

Indicates boat position and heading.

H Routepoint information

Indicates the distance to the routepoint, the routepoint
name, and the estimated time to reach the routepoint.

The Position panels

You can switch between displaying the Navigation panel or the
Position panel. The Position panel is activated from the menu.
By default, there is one position panel available showing GPS
position.
If Loran is enabled in the Navigation settings dialog, there are two
position panels. This is indicated with arrow symbols on left and
right side of the panel.
You toggle between the panels by:

•

selecting the left or right arrow symbols

GPS position info

Loran position info

64

Navigating

| GO XSE/XSR Operator Manual

«
...
62
63
64
65
66
...
»

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Бренд: Tascam Страницы: 128

Бренд: ParaBody Страницы: 6

Бренд: J.P. SELECTA Страницы: 32

Бренд: Laserworld Страницы: 8

Бренд: Laserworld Страницы: 6

Бренд: LaserLiner Страницы: 56

Бренд: LaserLiner Страницы: 54

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 114

Бренд: Posture Pump Страницы: 2

Бренд: LSI Страницы: 24

Бренд: olympia electronics Страницы: 2

Бренд: Phenix Technologies Страницы: 39

Бренд: Triton Страницы: 31

Бренд: GE Страницы: 644

Бренд: Kelvin Страницы: 30

Бренд: Daekyung Страницы: 15

Бренд: popular Страницы: 27

Бренд: Hella Gutmann Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды