manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Ú

Note: 

The distance between any waypoints in a route must not

be smaller than the radius of the waypoint arrival circle.

XTE limit

Defines how far the vessel can deviate from the selected route. If
the vessel goes beyond this limit, an alarm is activated.

Arrival alarm

When the arrival alarm is enabled, an alarm is activated when the
vessel reaches the waypoint or when it is within the specified arrival
radius.

Magnetic variation

Magnetic variation is the difference between true bearings and
magnetic bearings, caused by different locations of the Geographic
and the Magnetic north poles. Any local anomalies such as iron
deposits might also affect the magnetic bearings.
When set to Auto, the system automatically converts magnetic
north to true north. Select manual mode if you need to enter your
own local magnetic variation.

Datum

This system uses the WGS datum format, which is a standard for use
in cartography and satellite navigation (including GPS).
You can change the datum format to match other systems.

Coordinate system

Used to set the geographic coordinate system used on your system.

Navigating

 | GO XSE/XSR Operator Manual

67

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

ABB ACS880 Series Electrical Planning Manual preview
ACS880 Series
Бренд: ABB Страницы: 50
ABB ACS880-01 Series User Manual preview
ACS880-01 Series
Бренд: ABB Страницы: 17
ABB ACS880 Series User Manual preview
ACS880 Series
Бренд: ABB Страницы: 36
Zetec TOPAZ Technical Manuallines preview
TOPAZ
Бренд: Zetec Страницы: 23
Fisher Scientific Isotemp User Manual preview
Isotemp
Бренд: Fisher Scientific Страницы: 42
LANGER EMV-Technik P1401 User Manual preview
P1401
Бренд: LANGER EMV-Technik Страницы: 25
Lang Electric Clamshell CSE12-208VCD Installation, Operation And Maintenance Instructions preview
Electric Clamshell CSE12-208VCD
Бренд: Lang Страницы: 16
Landoll Brillion 3631-25 Operator'S Manual preview
Brillion 3631-25
Бренд: Landoll Страницы: 138
National Instruments NI VISION PCI-8254R Getting Started preview
NI VISION PCI-8254R
Бренд: National Instruments Страницы: 13
National Instruments NI VISION PCI-8254R Quick Start Manual preview
NI VISION PCI-8254R
Бренд: National Instruments Страницы: 16
National Instruments NI-9230 Getting Started preview
NI-9230
Бренд: National Instruments Страницы: 10
National Instruments myDAQ User Manual preview
myDAQ
Бренд: National Instruments Страницы: 39
National Instruments MXI Getting Started preview
MXI
Бренд: National Instruments Страницы: 65
haacon 4551 Operating Manual preview
4551
Бренд: haacon Страницы: 59
Nectar Pacer Using Manual preview
Pacer
Бренд: Nectar Страницы: 46
Neauvia PLASMA IQ Training Manual preview
PLASMA IQ
Бренд: Neauvia Страницы: 17
York 1002 Assembly Instruction Manual preview
1002
Бренд: York Страницы: 26
Martin Maxedia 4 User Manual preview
Maxedia 4
Бренд: Martin Страницы: 202

Бренды по названию

Популярные бренды

Загрузить еще бренды