manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Color

Strong and weak echo signals have different colors to indicate the
different signal strengths. The colors used depend on which palette
you select.
The more you increase the color setting, the more echoes are
displayed in the color at the strong return end of the scale.

Source

Ú

Note: 

Available only if multiple sources with the same

capability are available.

Used to specify the source for the image in the active panel.
You can display different sources simultaneously, using a multi-
panel page configuration. Menu options for each panel are
independent.

Ú

Note: 

Using transducers at the same frequency can cause

interference.

For source setup information, refer to the unit's Installation Manual.

Advanced options

The Advanced menu option is only available when the cursor is not
active.

Noise rejection

Filters out signal interference and reduces on-screen clutter.

TVG

Wave action and boat wakes can cause onscreen clutter near the
surface. The TVG (Time Variable Gain) option reduces surface clutter
by decreasing the sensitivity of the receiver near the surface.

Scroll speed

You can select the scrolling speed of the image on the screen. A
high scroll speed updates the image quicker, while a low scroll
speed presents a longer history.

152

Echosounder

 | GO XSE/XSR Operator Manual

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Magicfx FX-ARM CONTROLLER User And Installation Manual preview
FX-ARM CONTROLLER
Бренд: Magicfx Страницы: 16
CAIRE Focus Quick Reference Manual preview
Focus
Бренд: CAIRE Страницы: 2
7th Sense medialon Showmaster Go User'S Reference Manual preview
medialon Showmaster Go
Бренд: 7th Sense Страницы: 9
Paia 4712 Assembly And Using Manual preview
4712
Бренд: Paia Страницы: 11
CAB 4414 Series Service Manual preview
4414 Series
Бренд: CAB Страницы: 39
CAB FM1 Instruction Manual preview
FM1
Бренд: CAB Страницы: 27
Calix 804Mesh Quick Start Manual preview
804Mesh
Бренд: Calix Страницы: 9
Califone WT1 User Manual preview
WT1
Бренд: Califone Страницы: 7
CALITEK Grizzly 600 Manual preview
Grizzly 600
Бренд: CALITEK Страницы: 16
LAHTI PRO 46033 User Manual preview
46033
Бренд: LAHTI PRO Страницы: 20
LAHTI PRO 46017 User Manual preview
46017
Бренд: LAHTI PRO Страницы: 16
J&M 32 Series Operator'S Manual preview
32 Series
Бренд: J&M Страницы: 53
Qazqa 46060 Instruction Manual preview
46060
Бренд: Qazqa Страницы: 2
Tascam SX-1 Brochure & Specs preview
SX-1
Бренд: Tascam Страницы: 8
JBL MBB2020 Operation Manual preview
MBB2020
Бренд: JBL Страницы: 9
JBL EON15 Introduction And General Information preview
EON15
Бренд: JBL Страницы: 38
JBSYSTEMS Light FALCON Operation Manual preview
FALCON
Бренд: JBSYSTEMS Light Страницы: 32
JBM 53724 Manual preview
53724
Бренд: JBM Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды