Simrad GO XSE Series Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 242

background image

Copyright

Copyright © 2021 Navico Holding AS.

Warranty

The warranty card is supplied as a separate document. In case of any
queries, refer to the brand website of your unit or system:
www.simrad-yachting.com

Compliance statements

Declarations

The relevant declarations of conformity are available at:
www.simrad-yachting.com

Europe

Navico declare under our sole responsibility that the product
conforms with the requirements of:

•

CE under RED 2014/53/EU

United States of America

Navico declare under our sole responsibility that the product
conforms with the requirements of:

•

Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation

Warning:

The user is cautioned that any changes or

modifications not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.

Ú

Note:

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio

Preface

| GO XSE/XSR Operator Manual

5

«
...
3
4
5
6
7
...
»

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Бренд: Taurus Страницы: 28

Бренд: Kärcher Страницы: 54

Бренд: ABB Страницы: 85

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: UFO Страницы: 16

Бренд: ACDC Страницы: 4

Бренд: ZIGBEE Страницы: 4

Бренд: CAIRE Страницы: 38

Бренд: Caframo Страницы: 72

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 188

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 6

Бренд: Ecco Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды