SEW MOVITRAC MC07B0037-2A3-4-00 Скачать руководство пользователя

Страница: 141 / 252

System Manual V2 – MOVITRAC® B

141

Parameter set switchover

Project Planning

6.17

Parameter set switchover

This function is used to operate two motors on one inverter using two different parameter
sets.

The parameter set is switched over via binary input or fieldbus. A binary input must be
programmed to the "Parameter set switchover" function

(→

P60_/P61_) for this

purpose. You can then change from parameter set 1 to 2 and vice versa in INHIBITED
inverter status.

Function

Effect at

"0" signal

"1" signal

PARAM. SELECT

Parameter set 1 active

Parameter set 2 active

NOTE

A changeover contactor should be provided for each of the two motor cables when two
motors are operated alternately on the same inverter with the parameter set
switchover function in use. Only switch changeover contactors when the unit is
inhibited!

Содержание MOVITRAC MC07B0037-2A3-4-00





























































































































































































































































Результаты поиска

Содержание MOVITRAC MC07B0037-2A3-4-00

Отзывы:

Похожие инструкции для MOVITRAC MC07B0037-2A3-4-00

Бренды по названию

Популярные бренды

SEW MOVITRAC MC07B0037-2A3-4-00, Системное руководство

Результаты поиска

Содержание MOVITRAC MC07B0037-2A3-4-00

Отзывы:

Похожие инструкции для MOVITRAC MC07B0037-2A3-4-00

Бренды по названию

Популярные бренды