SEW MOVITRAC MC07B0037-2A3-4-00 Скачать руководство пользователя

Страница: 101 / 252

System Manual V2 – MOVITRAC® B

101

Explanation of the parameters

Parameters

540

Response to drive vibration /
warning

Factory setting: Display error
Once the drive vibration sensor signals a warning, the inverter will respond with
the set response.

541

Response to drive vibration /
fault

Factory setting: Rapid stop / warning
Once the drive vibration sensor signals a fault, the inverter will respond with the
set response.

542

Response to oil aging / warning

Factory setting: Display error
Once the oil aging sensor signals a warning, the inverter will respond with the
set response.

543

Response to oil aging / fault

Factory setting: Display error
Once the oil aging sensor signals a fault, the inverter will respond with the set
response.

544

Oil aging / overtemperature

Factory setting: Display error
Once the oil aging sensor signals overtemperature, the inverter will respond
with the set response.

545

Oil aging / ready signal

Factory setting: Display error
Once the oil aging sensor signals ready, the inverter will respond with the set
response.

549

Response to brake wear

Factory setting: Display error
Once the brake wear sensor signals a fault, the inverter will respond with the set
response.

6__

Terminal assignment

60_

Binary inputs (DI01 with fixed assignment to CW/STOP)

Effect of

0 signal

1 signal

Takes effect when: No enable

0: No function:

–

1: Enable / Stop:

Stop at

P136 Stop ramp

Enable

2: CW / stop:

Stop at

P131 Ramp down

Enable CW

3: CCW / stop:

Stop at

P131 Rampe down

Enable CCW

4: n11 / n21

5: n12 / n22

6: Fixed setpoint switchover:

Fixed setpoints n11/n12/n13

Fixed setpoints n21/n22/n23

yes

7: Parameter set switchover:

Parameter set 1

Parameter set 2

yes

8: Ramp switchover:

t11/t21 active

t12/t22 active

yes

9: Motor potentiometer up:

–

Increase setpoint

10: Motor potentiometer down:

–

Decrease setpoint

11: /External fault:

External fault

–

12: Fault reset:

Reset on positive edge 0 to 1

yes

19: Free-running slave:

Master-slave mode

Free-running slave

yes

20: Setpoint acceptance active:

Do not accept

Accept setpoint

26: TF signal (DI05 only):

Motor overtemperature

No signal

27: Vibration / warning

Sensor signals warning

Sensor does not signal warning

yes

28: Vibration / fault

Sensor signals fault

Sensor does not signal fault

yes

29: Brake wear

Brake is worn

Brake OK

yes

30: /Controller inhibit:

Inhibited

Enable

yes

33: Oil aging / warning

Sensor signals warning

Sensor does not signal warning

yes

34: Oil aging / fault

Sensor signals fault

Sensor does not signal fault

yes

35: Oil aging / overtemperature

Sensor signals overtemperatureSensor does not signal overtemperatureyes

36: Oil aging / ready

Sensor not ready

Sensor ready

yes

Fixed setpoints

n11/n21 = 0 and n12/n22 = 0:

External setpoints only

n11/n21 = 1 and n12/n22 = 0:

n11/n21

n11/n21 = 0 and n12/n22 = 1:

n12/n22

n11/n21 = 1 and n12/n22 = 1:

n13/n23

601

Binary input DI02

Factory setting: CCW/stop

602

Binary input DI03

Factory setting: Enable

603

Binary input DI04

Factory setting: n11/n21

604

Binary input DI05

Factory setting: n12/n22

608

Binary input DI00

Factory setting: Fault reset

No.

FBG

Name

Description

kVA

Содержание MOVITRAC MC07B0037-2A3-4-00





























































































































































































































































Результаты поиска

Содержание MOVITRAC MC07B0037-2A3-4-00

Отзывы:

Похожие инструкции для MOVITRAC MC07B0037-2A3-4-00

Бренды по названию

Популярные бренды

SEW MOVITRAC MC07B0037-2A3-4-00, Системное руководство

Результаты поиска

Содержание MOVITRAC MC07B0037-2A3-4-00

Отзывы:

Похожие инструкции для MOVITRAC MC07B0037-2A3-4-00

Бренды по названию

Популярные бренды