SCHUNK ORG 85 Скачать руководство пользователя страница 83

Страница: 83 / 92

Maintenance

03.00 | ORG | Assembly and Operating Manual | en | 389246

7.7.1 Disassembling assembly group 1 (Triple jaw unit A)

Position of the item numbers

NOTE

Turn off the compressed air supply for all compressed air
connections and detach all compressed air lines from the gripper!

Mark the assembly position of the base jaws (16) in the base
bodies triple jaw A (5).

Detach the three cylindrical pins (60) which connect the base
jaws (16) with the angle levers triple jaw A (17).

Pull the base jaws (16) radially out of the base body triple jaw A (5).

Detach the three cylindrical pins (69) which connect the fork
head (14) with the angle levers triple jaw A (17).

Detach the three cylindrical pins (60) supporting the angle
levers triple jaw A (17) in the base body triple jaw A (5).

The three angle levers triple jaw A (17) can be removed.

Unscrew the three screws (42) with the spacer sleeves (6).

Remove the three base body triple jaws A (5) toward the top
from the flange (10).

Detach the six cylindrical pins (61) from the flange (item 10).

Detach the cylindrical bushing (8) from the flange (10).

Loosen the screw (44) connecting the piston rod (9) with the
triple jaw A piston (15).

Turn the set screw (45) out of the piston rod (9).

Pull the fork head (14) toward the top out of the flange (10).

Turn the piston rod (9) upward out of the fork head (14).

NOTE

Assembly is carried out in reverse order whereby the following
notes need to be observed for the assembly of assembly group 1:

Observe notes in this chapter

Notes

[

}

79], the necessary

utensils for maintenance

Utensils required for maintenance

[

}

79] as well as the screw

tightening torques

Screw tightening torque

[

}

80].

The base jaws (16) must be assigned to the base bodies triple
jaw A (5) which were marked earlier!

All nine cylindrical pins (60 and 69) must be positioned in the
centre of angle lever triple jaw A (17)!

The set screw (45) is acting as anti-rotation device for the screw
(44). That means, after the assembling of the piston (15) and
the screw (44), the screw (44) has to be clamped with the set
screw (45)!

Содержание ORG 85





























































































Результаты поиска

Содержание ORG 85

Отзывы:

Бренды по названию

Популярные бренды

SCHUNK ORG 85, Сборка и руководство по эксплуатации

Результаты поиска

Содержание ORG 85

Отзывы:

Бренды по названию

Популярные бренды