Samson 3730-4 Скачать руководство пользователя | Manualshive

Страница: 64 / 100

background image

CHECK_BACK_MASK (50)

Storage class: – · Read capability (r)

Defines the supported status bits in CHECK_BACK
Bit = 0: Status not supported
Bit = 1: Status supported

CHECK_BACK_OPT (65)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL
This alarm does not apply for acyclic access

Defines the support of the status bit in CHECK_BACK for cyclic data exchange
• [0x8F, 0xEC, 0x83]
• Bit = 0 · Status not supported
• Bit = 1 · Status supported

FSAFE_TIME (39)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Fail-safe time [s]
Time from detection of failure of the setpoint valid for the AO Function Block in the current mode until

the fail-safe action is triggered
• [0]

Note:

If the error still persists after the fail-safe time has elapsed, fail-safe action is triggered. The

fail-safe action of the AO Function Block is determined by FSAFE_TYPE in this Block.

FSAFE_TYPE (40)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Fail-safe action
Defines the reaction to be taken when a communication failure is detected or after a warm start
• 0 · The default value FSAFE_VALUE is used
• 1 · The last valid setpoint is used/The last valid setpoint is saved
• 2 · Actuator moves to the fail-safe position defined by the actuator springs

FSAFE_VALUE (41)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Fail-safe value
Default value for setpoint (reference variable w) used when a communication failure is detected or after

a warm start

64

KH 8384-4 EN

AO Function Block, Slot 1

· Profile-specific parameters

«
...
62
63
64
65
66
...
»

Содержание 3730-4





































































































Отзывы:

Нет отзывов

Похожие инструкции для 3730-4

Бренд: cascade corporation Страницы: 24

Бренд: Aacraft Страницы: 2

Бренд: PMK Страницы: 4

Бренд: Bürkert Страницы: 196

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды