Samson 3730-4 страница 44 Скачать руководство пользователя

Страница: 44 / 100

FEATURE (42)

Storage class: – · Read capability (r)

Optional existence and state of the feature integrated into the device
Supported/enabled (

Note:

The structure for supported and enabled are identical!)

• 0 = Not supported/not enabled
• 1 = Supported/enabled

Byte

Bit

Element

[Default]

Description

CONDENSED_STATUS

[1]

Status and diagnosis complying

with 'condensed status and diagnostic

messages' extension

EXPANDED_STATUS/DIAGNOSIS

[1]

Status and diagnostics acc. to

Profile 3.01

2…7

Reserved

[0]

0…7

Reserved

[0]

0…7

Reserved

[0]

0…7

Reserved

[0]

HARDWARE_REVISION (25)

Storage class: – · Read capability (r)

Hardware version (electronics/mechanics)

HW_WRITE_PROTECTION (41)

Storage class: – · Read capability (r)

Position of the write protection switch on the device
• 0 · Not write-protected
• 1 · Write-protected

IDENT_NUMBER_SELECTOR (40)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Used to select the ID number
• 0 · Profile-specific ID (0x9710), PA139710.GSD
• 1 · Manufacturer-specific ID (0x07ID), SAMS071D.GSD

LOCAL_OP_ENA (39)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Local operation enabled

If communication fails for a time longer than 30 seconds, local operation will be enabled automatically
• 0 · Disabled
• 1 · Enabled

KH 8384-4 EN

Physical Block, Slot 0 ·

Profile-specific parameters

Содержание 3730-4





































































































Результаты поиска

Содержание 3730-4

Отзывы:

Похожие инструкции для 3730-4

Бренды по названию

Популярные бренды

Samson 3730-4, Руководство по настройке

Результаты поиска

Содержание 3730-4

Отзывы:

Похожие инструкции для 3730-4

Бренды по названию

Популярные бренды