Samson 3730-4 Скачать руководство пользователя страница 98

Страница: 98 / 100

ST_REV (61)

Storage class: S · Read capability (r)

Revision level of static data

STRATEGY (63)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Grouping to allow faster processing of blocks
• [0]
Blocks are grouped by entering the same value in the STRATEGY parameter of each block.

TAG_DESC (62)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Assigns a unique description to each block for clear identification.
• Max. 32 characters

TARGET_MODE (65)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Target mode
• 8 · AUTO
• 16 · MAN
• 128 · O/S

Index and parameter assignment:

DI1/2 Transducer Block, Slot 2/3 · Profile-specific pa-

rameters

KH 8384-4 EN

DI1/2 Transducer Block, Slot 2/3

· Profile-specific parameters

Index Parameter

BLOCK_OBJ

ST_REV

TAG_DESC

STRATEGY

ALERT_KEY

TARGET_MODE

Index Parameter

MODE_BLK

ALM_SUM

SENSOR_WIRE_CHECK

SENSOR_ID

SENSOR_MAN

PV_D

Содержание 3730-4





































































































Результаты поиска

Содержание 3730-4

Отзывы:

Бренды по названию

Популярные бренды

Samson 3730-4, Руководство по настройке

Результаты поиска

Содержание 3730-4

Отзывы:

Бренды по названию

Популярные бренды