Samson 3730-4 страница 31 Скачать руководство пользователя

Страница: 31 / 100

The default setting causes the positioner to provide a manufacturer-specific diagnosis of 26

bytes and a diagnosis of 14 bytes according to Profile 3.01.

Octet

Bit Explanation

Note

0…7

Standard slave diagnostics

0…7

Definition of manufacturer-specific diagnostic alarms

0…7

DIA_HW_ELECTR (hardware fault in the electronics)

DIA_HW_MECH (hardware fault in the mechanics)

Not assigned

DIA_TEMP_ELECTR (temperature of electronics too high)

DIA_MEM_CHCKSUM (checksum error in data memory)

DIA_MEASUREMENT (error in measurement)

DIA_NOT_INIT (device not initialized/self-calibration not performed)

DIA_INIT_ERR (self-calibration faulty)

DIA_ZERO_ERR (zero point error, final position)

–

DIA_CONF_INVAL (configuration invalid/invalid address)

DIA_WARMSTART (restart-up/warm start performed)

DIA_COLDSTART (new start-up/cold start performed)

DIA_MAINTENANCE (maintenance required)

DIA_CHARACT (characteristic invalid)

IDENT_NUMBER_VIOLATION (selected ID no. has not been implemented by the device yet)

DIA_MAINTENANCE_ALARM (device error exists)

DIA_MAINTENANCE_DEMANDED (maintenance demanded)

DIA_FUNCTION_CHECK (device in function check, in simulation or in MODE_LO)

DIA_INV_PRO_COND (process-related fault/out of specification)

KH 8384-4 EN

Standard diagnostics with PROFIBUS-DP protocol

Содержание 3730-4





































































































Результаты поиска

Содержание 3730-4

Отзывы:

Похожие инструкции для 3730-4

Бренды по названию

Популярные бренды

Samson 3730-4, Руководство по настройке

Результаты поиска

Содержание 3730-4

Отзывы:

Похожие инструкции для 3730-4

Бренды по названию

Популярные бренды