Samson 3730-4 Скачать руководство пользователя страница 75

Страница: 75 / 100

KH 8384-4 EN

AO Transducer Block, Slot 1

· Profile-specific parameters

TRAVEL_LIMIT_LOW (127)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Travel/angle lower limit [% of PV_SCALE] (Code 10)
Limitation of the travel/angle of rotation downwards to the entered value. The characteristic is not

adapted.
• [0.0 %]

TRAVEL_LIMIT_UP (128)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Travel/angle upper limit [% of PV_SCALE] (Code 11)
Limitation of the travel/angle of rotation upwards to the entered value. The characteristic is not

adapted.
• [100.0 %]

TRAVEL_RATE_DEC (129)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Required transit time CLOSED [s]
Minimum time required to move through the working range to 0 % position
• [0.0 s]

TRAVEL_RATE_INC (130)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Required transit time OPEN [s]
Minimum time required to move through the working range to 100 % position
• [0.0 s]

VALVE_MAINT_DATE (131)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Date of the last maintenance performed on the positioner [XX.XX.20XX]

VALVE_MAN (139)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Valve manufacturer

VALVE_SER_NUM (144)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Serial number of the valve

Содержание 3730-4





































































































Результаты поиска

Содержание 3730-4

Отзывы:

Бренды по названию

Популярные бренды

Samson 3730-4, Руководство по настройке

Результаты поиска

Содержание 3730-4

Отзывы:

Бренды по названию

Популярные бренды