Samson 3730-4 Скачать руководство пользователя страница 65

Страница: 65 / 100

IN_CHANNEL (37)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Assignment between the Transducer Block and the Function Block
• 0 · Not active
• 0x013A · Active (FEEDBACK_VALUE is written to READBACK)

INCREASE_CLOSE (52)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Determines the direction of action, i.e. how the reference variable is assigned to the controlled variable
• Increasing/increasing
• Increasing/decreasing

MODE_BLK (22)

Storage class: – · Read capability (r)

Current mode

OUT (53)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Output value
This output value is calculated by the Function Block from the SETPOINT for the Transducer Block in

[mm], [degrees] or [%]

OUT_CHANNEL (38)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Assignment between the Transducer Block and the Function Block
• 0 · Not active
• 0x0139 · Active (OUT is written to POSITIONING_VALUE)

OUT_SCALE (54)

Storage class: S · Read/write capability (r/w) · Supported modes: O

Travel range or angle of rotation
Upper and lower values of the actual working range in [mm] or [degrees]. A non-linear characteristic is

adapted to the reduced travel.
Maximum value for upper value = Rated travel

KH 8384-4 EN

AO Function Block, Slot 1

· Profile-specific parameters

Содержание 3730-4





































































































Результаты поиска

Содержание 3730-4

Отзывы:

Бренды по названию

Популярные бренды

Samson 3730-4, Руководство по настройке

Результаты поиска

Содержание 3730-4

Отзывы:

Бренды по названию

Популярные бренды