Samson 3730-4 Скачать руководство пользователя

Страница: 79 / 100

DEVICE_CHARACT (202) and DEVICE_CHARACT_2 (231)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Structure of the device properties

Element

Parameter

Actuator effective area

Type of actuator

Attachment

Lower signal pressure range

Upper signal pressure range

Supply pressure

Booster

Stem packing

Plug/seat facing (leakage class)

Pressure balancing

Flow characteristic

Direction of flow

Nominal size standard

Nominal size DN

unit

coefficient

Seat diameter of the valve

DEVICE_INIT_STATE (163)

Storage class: – · Read capability (r)

Indicates whether the device has been initialized.

DIAG_MONITORING (187)

Storage class: – · Read capability (r)

Temperature-specific parameter

Element

Parameter

CURRENT_TEMP (current temperature)

MAX_TEMP (max. temperature)

TIME_MAX_TEMP (time at which max. temperature occurred)

MIN_TEMP (min. temperature)

TIME_MIN_TEMP (time at which min. temperature occurred)

PERIOD_TIME_HIGH (period of time max. temperature lasted)

PERIOD_TIME_LOW (period of time min. temperature lasted)

KH 8384-4 EN

AO Transducer Block, Slot 1

· Manufacturer-specific parameters

Содержание 3730-4





































































































Результаты поиска

Содержание 3730-4

Отзывы:

Похожие инструкции для 3730-4

Бренды по названию

Популярные бренды

Samson 3730-4, Руководство по настройке

Результаты поиска

Содержание 3730-4

Отзывы:

Похожие инструкции для 3730-4

Бренды по названию

Популярные бренды