Samson 3730-4 Скачать руководство пользователя

Страница: 29 / 100

Fault/diagnostic alarm

Default setting acc. to Pro-

file 3.01 Condensed Status

Classified

Diagnosis

Yes

Mostly max. opening

0x80 GOOD_NON_SPECIFIC

•

–

Temperature monitoring

Lower limit exceeded

0x80 GOOD_NON_SPECIFIC

•

–

Higher limit exceeded

0x80 GOOD_NON_SPECIFIC

•

–

Reference run

Reference test aborted

0x80 GOOD_NON_SPECIFIC

•

–

ESD

Movement actuator possible –>

Masking redundant

0x80 GOOD_NON_SPECIFIC

•

–

Movement actuator impossible

0x80 GOOD_NON_SPECIFIC

•

–

Solenoid valve error

0x80 GOOD_NON_SPECIFIC

•

–

Function activated

Initialization active

0xBC GOOD_NON_SPECIFIC

•

–

Diagnostic function active

0xBC GOOD_NON_SPECIFIC

•

–

Can be classified either as GOOD_FUNCTION_CHECK or BAD_FUNCTION_CHECK in firmware K 1.10 and

higher. See FEATURE_SELECT parameter on page 54.

5.5

Standard diagnostics with PROFIBUS-DP protocol

Generated alarms are classified and summarized in the PROFIBUS Profile 3.01 and 'Con-

densed status and diagnostic messages' extension.
The diagnostic approach complying with PROFIBUS-DP includes the following types of diag-

nostic transfer:

The DP master class 1 reads the diagnosis of the DP slave while the cyclic data exchange

is being set up.

In case of an active diagnostic alarm, the slave responds during the data exchange with a

high-prioritized response telegram.

The master requests a diagnosis as a result to continue afterwards with the normal data

exchange.

KH 8384-4 EN

Measured value status and valve diagnostics

Содержание 3730-4





































































































Результаты поиска

Содержание 3730-4

Отзывы:

Похожие инструкции для 3730-4

Бренды по названию

Популярные бренды

Samson 3730-4, Руководство по настройке

Результаты поиска

Содержание 3730-4

Отзывы:

Похожие инструкции для 3730-4

Бренды по названию

Популярные бренды