Samson 3730-4 Скачать руководство пользователя

Страница: 19 / 100

The condensed state is displayed in the engineering tool and on the positioner display (see

table below).

Status modification

The classification of the status alarms can be assigned as required using the TROVIS-VIEW

software connected to the local SSP interface of the positioner or over the PA parameters.

NOTICE

All extended alarms generated by the EXPERTplus diagnostics are assigned the “No messa-

ge” status by default.

Logging and displaying diagnostic functions/alarms

The last 30 alarms are logged in the positioner. An alarm that is repeated is only logged

once when it first occurs.

The alarms and the condensed state appear on the display as described in the code list (refer

to EB 8384-4 EN). In addition, the diagnostic parameters are available over the communica-

tion interface of the positioner. The diagnostic functions can easily be displayed and config-

ured using the TROVIS-VIEW software connected over the local interface (SSP) or over the

PROFIBUS protocol.
The COND_STATUS_DIAG parameter in the Physical Block allows you to select whether the

measured value status is to be set according to Profile 3.01 or according to the 'Condensed

Status and diagnostic messages' profile extension.

KH 8384-4 EN

Measured value status and valve diagnostics

Status alarm

Engineering tool/

TROVIS-VIEW

(version 3.40 and higher)

Positioner display

No message, OK

green

Function check

orange

tEsting

tunE

tEst

Maintenance required
Maintenance demanded

blue

Process-related fault
Out of specification

yellow

Maintenance alarm

red

Condensed state

Содержание 3730-4





































































































Результаты поиска

Содержание 3730-4

Отзывы:

Похожие инструкции для 3730-4

Бренды по названию

Популярные бренды

Samson 3730-4, Руководство по настройке

Результаты поиска

Содержание 3730-4

Отзывы:

Похожие инструкции для 3730-4

Бренды по названию

Популярные бренды